bobcat code m0514

Bobcat Code M0514: Causes, Fixes & Troubleshooting Guide

By Brian Moore
AD

When a Bobcat machine flashes code M0514, the operator usually sees a warning, hears an alarm, and notices reduced hydraulic performance. The code is commonly tied to the hydraulic oil temperature sensor circuit, specifically a short to ground. Because hydraulic oil temperature affects everything from loader response to cooling fan strategy, the controller takes this signal seriously. Ignoring it can turn a simple sensor or wiring repair into a much larger hydraulic problem.

This guide covers what Bobcat code M0514 means, the symptoms it causes, likely causes, diagnostic steps, repair costs, and prevention. It applies broadly to Bobcat skid steers, compact track loaders, and some mini excavators that use similar machine control systems. Always verify the exact definition in your model and serial number service manual before ordering parts.

What Bobcat Code M0514 Means

M0514 is a machine fault code stored in the Bobcat controller. In most service literature, it indicates that the hydraulic oil temperature sensor signal circuit has been detected as shorted to ground. The controller monitors a voltage or resistance signal from the sensor and compares it to expected values. When the signal drops outside the normal range, the controller logs M0514 and may substitute a default temperature value.

AD
BOBCAT 371 SKID STEER LOADER REPAIR MANUAL
BOBCAT 371 SKID STEER LOADER REPAIR MANUAL
☆ bobcat therian ☆
☆ bobcat therian ☆
a yellow skid steer sitting on top of a brick road
a yellow skid steer sitting on top of a brick road

The hydraulic oil temperature sensor is usually located on or near the hydraulic tank, return filter housing, or oil cooler. It tells the controller how hot the hydraulic oil is so the machine can adjust cooling fan speed, warn the operator, or derate hydraulic functions to prevent damage. A short to ground can make the controller think the oil is extremely hot even when it is not.

Common Symptoms of M0514

The most obvious symptom is a fault code displayed on the operator interface or diagnostic screen. You may also see a hydraulic oil temperature warning light, an audible alarm, or a gauge reading that spikes to the maximum. In some machines, the cooling fan may run at full speed constantly because the controller believes the oil is overheated.

the logo for bobcat is shown in white on a red background with an image of a cat's head
the logo for bobcat is shown in white on a red background with an image of a cat's head
a large cat standing on top of a dirt field
a large cat standing on top of a dirt field
2024 Bobcat MT100 for Sale
2024 Bobcat MT100 for Sale

Performance symptoms can include sluggish hydraulics, reduced travel speed, limited lift or tilt response, and a forced limp mode. The code may appear only when the machine is warm, after hitting a bump, or when the harness is wet. Intermittent symptoms often point to chafed wiring or a connector with moisture rather than a failed sensor.

Systems and Models That Can Store M0514

Bobcat M0514 is most frequently reported on skid steer loaders and compact track loaders such as the S-series and T-series, but similar codes can appear on other Bobcat equipment. The exact code definition can vary by model year, controller family, and engine package, so a 2015 T650 may not use the same diagnostic path as a 2020 S770.

AD

If your machine uses a different sensor architecture or a CAN-based hydraulic controller, the code may still relate to hydraulic oil temperature but with different pin locations and voltage values. That is why the model and serial number are essential when looking up wiring diagrams, sensor resistance charts, and repair procedures.

a cat is running through the snow in front of some stars and shapes on it
a cat is running through the snow in front of some stars and shapes on it
Dealer Watch: Bobcat Company Introduces Two New Authorized Dealers in Florida
Dealer Watch: Bobcat Company Introduces Two New Authorized Dealers in Florida
MT100 Skid Steer
MT100 Skid Steer
Bobcat MT55 with Augear how to drill a hole pcrsol
Bobcat MT55 with Augear how to drill a hole pcrsol
an orange and white skid steer sitting in the middle of a dirt field next to a tractor
an orange and white skid steer sitting in the middle of a dirt field next to a tractor
Next theiran type?
Next theiran type?

Common Causes Behind a Bobcat M0514 Fault

A short to ground in the hydraulic oil temperature circuit is the core trigger for M0514. The short can happen inside the sensor, inside a connector, or along the length of the harness. Because Bobcat machines operate in dirty, vibrating, and wet conditions, wiring problems are just as common as sensor failure.

Diagnosing the cause requires separating the sensor from the harness. If the code disappears when the sensor is unplugged, the sensor may be internally shorted. If the code remains or changes when you wiggle the harness, the problem is likely in the wiring, connector, or controller. A methodical approach prevents replacing good parts.

AD

Sensor and Connector Problems

Hydraulic oil temperature sensors can fail internally due to age, heat cycles, contamination, or mechanical damage. A failed sensor may read open, shorted, or stuck within a narrow range. Corrosion inside the connector is another frequent culprit, especially if the machine is pressure-washed or used in wet environments.

bi bobcat pfp * requested*
bi bobcat pfp * requested*
a bobcat walking in the snow with it's head turned towards the camera
a bobcat walking in the snow with it's head turned towards the camera
a cat sitting on top of a tree branch in the middle of snow covered ground
a cat sitting on top of a tree branch in the middle of snow covered ground
Bobcat Logo
Bobcat Logo

Look for green or white corrosion on the terminals, loose female pins, cracked connector housings, and pushed-back wires. Moisture can bridge terminals and create a temporary short to ground. Cleaning and drying the connector may fix the issue briefly, but if corrosion has damaged the pins, replacement of the connector pigtail is the durable repair.

Wiring Harness and Ground Faults

The sensor signal wire can rub through against the frame, engine components, or hydraulic lines. A chafed wire may short to ground only when the machine vibrates or turns, which explains intermittent M0514 codes. Rodent damage, pinched harnesses near the cab, and repairs from previous owners can also create hidden shorts.

AD

Ground faults are not always obvious. A wire may look fine but have internal corrosion that allows the signal to bleed to ground. Use a wiring diagram to identify the signal, ground, and reference pins, then perform continuity and resistance tests. Wiggle tests while watching live data can reveal faults that a static meter check misses.

How to Diagnose and Repair Bobcat Code M0514

Before diagnosing M0514, park the machine on level ground, lower the lift arms, engage the parking brake, shut off the engine, and allow the hydraulic system to cool. Hydraulic oil can be hot enough to cause severe burns, and pressurized lines can inject fluid. Wear safety glasses and gloves, and never disconnect hydraulic components while the system is hot or pressurized.

Use the machine display or a diagnostic tool to retrieve active and stored codes. Record all codes, not just M0514, because related faults can point to a common power or ground issue. Clear the code only after documenting it. If it returns immediately with the key on, the short is likely present in the circuit.

Step-by-Step Troubleshooting Checklist

First, locate the hydraulic oil temperature sensor and inspect the connector and wiring. Disconnect the sensor and check for corrosion, moisture, bent pins, and damaged insulation. With the key on, check for the specified reference voltage at the harness connector. If the reference voltage is missing, inspect fuses, power supply, and ground circuits before blaming the sensor.

Next, measure the sensor resistance and compare it to the temperature chart for your machine. If the sensor is internally shorted, replace it. If the sensor tests good, check the signal wire for continuity to ground with the sensor and controller disconnected. Repair any short by soldering the wire, sealing it with heat shrink, and securing the harness away from sharp edges and heat sources.

After repairs, clear the codes and run the machine through a complete warm-up cycle. Watch live hydraulic oil temperature data on the diagnostic tool. The reading should rise gradually and match ambient and operating conditions. If M0514 returns, revisit the harness routing and controller connections, or consult a dealer for advanced diagnostics.

Repair Costs and Replacement Options

A replacement hydraulic oil temperature sensor often costs between $40 and $200 depending on the Bobcat model and whether it is an OEM or aftermarket part. A connector pigtail or repair kit may cost $20 to $80. Harness repair labor at a dealer or independent shop can range from $100 to $400 or more, depending on how much disassembly is required.

If the controller is diagnosed as faulty, costs rise significantly. A new or remanufactured Bobcat controller can run from several hundred to over a thousand dollars, plus programming and installation. Because controllers are rarely the root cause of M0514, do not replace one until the sensor, wiring, connectors, power, and grounds have been thoroughly tested.

Preventing M0514 and Keeping Your Bobcat Reliable

Preventing M0514 starts with clean hydraulic oil and a healthy cooling system. Contaminated oil can cause the hydraulic oil temperature sensor to read incorrectly and can accelerate wear inside the hydraulic system. Check oil levels daily, follow the manufacturer's service intervals, and use the specified hydraulic oil grade for your climate and application.

Regular electrical inspections also matter. Look for rubbed harnesses, loose connectors, and signs of moisture intrusion. Keep the engine compartment and hydraulic area clean, but avoid directing high-pressure water at electrical connectors. A little preventive attention can stop a small wiring fault from becoming an expensive diagnostic mystery.

Maintenance Habits That Reduce Fault Codes

Inspect the hydraulic oil cooler and fan for debris, bent fins, and blocked airflow. A restricted cooler raises oil temperature and makes the sensor work in harsher conditions. Check the cooling fan operation and ensure the fan drive system is functioning correctly, especially on machines that use variable-speed fan control.

During routine service, wiggle-test sensor harnesses and inspect connectors for corrosion. Apply dielectric grease only where the manufacturer recommends it, and replace damaged loom or conduit. Keep a log of fault codes and repairs so you can spot repeat issues before they strand the machine on a job site.

When to Call a Bobcat Technician

If you have checked the sensor, connector, and obvious harness damage but M0514 persists, it may be time for dealer-level diagnostics. A technician with Bobcat service software can view live data, perform output tests, and access model-specific wiring diagrams. This is especially important if the machine is under warranty or has complex CAN bus communications.

Call a professional also if you find hydraulic oil contamination, metal debris in the tank, or multiple related fault codes. Those symptoms can indicate a larger hydraulic pump, motor, or valve problem. Fixing the electrical code without addressing the mechanical cause may lead to repeat failures and costly downtime.

A Bobcat code M0514 is rarely a dead-end problem. It is a signal that the hydraulic oil temperature circuit needs attention, and in most cases the fix is a sensor, connector, or section of harness. By diagnosing logically and verifying repairs with live data, you can get your machine back to work without throwing parts at it. Keep your service manual handy, document what you find, and address small electrical issues before they become major breakdowns.

AD