AquaSource Henshaw Toilet Installation: Step-by-Step DIY Guide
The Aquasource Henshaw is one of the most popular toilets sold at Lowe's, and it earned that spot with a simple formula: a comfort-height elongated bowl, a 1.28-gallon-per-flush rating that keeps water bills in check, and a price tag that undercuts most of the big-name competition. What many buyers don't realize until they get the box home is that the Henshaw is a two-piece model, which means the bowl and tank arrive separately and must be joined, sealed, and leveled correctly before the first flush. Get that right and you'll forget the toilet is even in the house. Get it wrong and you'll be chasing a slow leak across the bathroom floor for months.
This guide walks through Aquasource Henshaw toilet installation from start to finish, covering the tools worth having on hand, how to pull the old fixture without making a mess, the order of operations for setting the bowl and mounting the tank, and the leak checks that separate a clean professional-looking job from a weekend hack. Most homeowners with basic tools can finish in about ninety minutes, though first-timers should budget two to three hours so there's no rushing. Before you start, confirm your rough-in measurement and check whether your local code requires a permit or a licensed plumber for fixture replacement.
Preparation, Measurements, and Removing the Old Toilet
The Aquasource Henshaw is built for a standard 12-inch rough-in, which is the distance from the finished back wall to the center of the closet flange bolts. Measure yours before you open anything. If you're sitting at 10 or 14 inches, the Henshaw won't fit without a offset flange or a different model, and discovering that after you've pulled the old toilet is a miserable way to spend a Saturday. Comfort-height models like the Henshaw also sit about 16.5 inches from floor to rim, so measure your cabinet clearance and towel bar placement if space is tight.
Inside the box you should find the bowl, tank, tank lid, tank-to-bowl gasket, tank bolts and washers, a wax ring, closet bolts, bolt caps, and a template or instruction sheet. A supply line is often sold separately, so pick one up in the correct length and consider adding a quarter-turn shutoff valve if your current one is seized or crusty. Aquasource offers both single-flush and dual-flush versions of the Henshaw, and the installation process is nearly identical for both, so the steps below apply to either. The only meaningful difference is the flush actuator on the dual-flush lid, which uses a cable or rod mechanism that needs to seat properly over the flush valve.
Tools and Supplies to Have Ready
You don't need a truckload of plumbing gear, but you do need the right basics: an adjustable wrench, a pair of channel-lock pliers, a putty knife, a utility knife, a sponge, a bucket, rubber gloves, a level, and a hacksaw in case you need to trim the closet bolts. A socket set or a basin wrench makes short work of the tank bolts and supply connection. Safety glasses and knee pads are worth grabbing too, especially if the floor is tile and you'll be kneeling on it for an hour.
On the consumables side, buy a fresh wax ring even if the one in the box looks fine, plus a tube of 100 percent silicone caulk and a roll of paper towels or old rags. A small container of plumber's putty is handy for a stubborn supply escutcheon. Keep a plastic shopping bag nearby for the old wax ring and bolts, and line your bucket with a garbage bag before you start bailing water out of the tank and bowl. Having everything staged in the bathroom doorway beats sprinting to the garage with a dripping bowl in your hands.
Pulling the Old Toilet Safely
Shut off the water at the wall valve and flush the toilet to drain the tank. Then sponge or bail out whatever remains in the tank and bowl, because a toilet holds more water than you think and gravity is not on your side during the lift. Disconnect the supply line from the fill valve, remove the tank from the bowl if you're scrapping the unit anyway, and then pop the decorative caps off the closet bolts and unscrew the nuts. If the base was caulked, run a utility knife around the perimeter first so you don't rip up the flooring when you lift.
Rock the bowl gently side to side to break the wax seal, then lift it straight up with a helper and set it on cardboard or a tarp. Stuff a rag into the open drain to block sewer gas while you work. Scrape the old wax off the flange with a putty knife, and inspect the flange itself for cracks, corrosion, or a broken bolt slot. A flange that sits below the finished floor or has a damaged ear is the single most common reason a new toilet wobbles or leaks, so address it now with a flange repair ring rather than hoping the wax ring compensates.
Installing the Aquasource Henshaw Bowl and Tank
With the flange clean and the floor clear, you're ready for the part that actually matters. Work on a flat surface with the bowl upside down if you prefer to seat the wax ring on the bowl outlet, or place the ring directly on the flange with the plastic funnel pointing down into the drain. Either method works, but never stack two rings and never reuse an old one. If you're installing on a floor with a flange that sits low, a jumbo or extra-thick wax ring buys you the extra sealing depth you need.
Seating the bowl is a one-shot operation. Lower it straight down over the closet bolts and the wax ring without rocking or twisting, then press down firmly and evenly with your body weight so the wax compresses against the flange. Once it's seated, don't lift it again to check your work, because the seal is already spent once it's compressed. If you do pull it up, replace the ring. A second person makes this step far easier, since a Henshaw bowl with the tank off still weighs somewhere in the neighborhood of fifty pounds.
Securing the Bowl and Setting the Tank
Slide the washers and nuts onto the closet bolts and tighten them alternately, a few turns at a time, until the bowl is snug against the floor. Snug is the goal, not tight. Over-torquing is how people crack porcelain and how they crush a wax ring until it oozes out the sides. Check for level in both directions, and if the floor slopes, slide plastic shims under the base at the low points rather than cranking the bolts to force it flat. Trim the bolts with a hacksaw once everything is tight, leaving just enough thread for the decorative caps.
Flip the bowl upright, set the tank-to-bowl gasket in place over the flush valve opening, and lower the tank onto the bowl. Feed the tank bolts through from inside the tank, add the rubber washers and nuts underneath, and tighten in a cross pattern. The rubber washers go inside the tank on most Henshaw models, and the metal washers and nuts go underneath the bowl ledge. Again, alternate and snug. Fill the tank about a third of the way with a bucket of water before bolting everything down to add weight and help the gasket seat evenly.
Connecting Water, Setting the Level, and Final Adjustments
Thread the new supply line onto the fill valve shank by hand, then give it a quarter turn with pliers. Repeat on the shutoff valve end. Turn the water on slowly and watch both connections for weeping. Inside the tank, adjust the fill valve so the water line lands about an inch below the top of the overflow tube or at the marked line molded on the tank wall. A Henshaw that's set too low will produce a weak, unsatisfying flush, while one set too high will run continuously into the overflow.
Check the flapper chain next. It should have roughly half an inch of slack, enough to lift the flapper fully but not so much that it gets caught under the flapper when it closes. If your Henshaw is the dual-flush version, verify that the actuator button on the lid lines up with the flush valve stem and that both the half and full flush positions release cleanly. Then flush the toilet five or six times in a row, watching the base, the tank bolts, and the supply line for any sign of moisture. Let it sit for a full day before caulking the base, so a slow leak has a chance to reveal itself instead of hiding behind a bead of silicone.
Testing, Troubleshooting, and Long-Term Care
After the first day, run a few more flush cycles and inspect again. When you're satisfied there's no weeping, caulk the base with 100 percent silicone, leaving a small gap at the front or back so future leaks have somewhere to show themselves. Skip the gap and a failing wax ring will quietly rot your subfloor instead. A bead of caulk around the base isn't just cosmetic, either; it stabilizes the bowl and keeps mop water and stray splashes from working under the porcelain.
Troubleshooting a newly installed Henshaw is usually straightforward because the failure points are limited. A rocking bowl means shims or a flange issue. A weak flush points to water level, a stretched chain, or a flapper that isn't sealing. A toilet that refills on its own every twenty minutes is a leaking flapper, and a puddle at the base almost always means the wax ring didn't seat. Sewer odor suggests the same thing, though it can also mean a dry trap in a rarely used floor drain nearby.
Leak Checks, Flush Tuning, and Water Efficiency
Run a dye test if you suspect a phantom flush: drop a few drops of food coloring in the tank, wait fifteen minutes without flushing, and check the bowl. Color in the bowl means water is escaping past the flapper. A new flapper costs a few dollars and takes two minutes to swap. If the toilet fills slowly, check that the shutoff valve is fully open and that the supply line isn't kinked behind the bowl. Mineral buildup in the fill valve screen is another common culprit in hard-water areas.
To get the most out of the Henshaw's 1.28-gallon flush, keep the water level at the manufacturer's mark and make sure the flapper lifts fully and drops cleanly. If you live in an older home with cast iron drain lines that have accumulated scale, you may need the full flush every time. In newer construction with properly sloped PVC, the standard setting handles everything short of an unusual load. Resist the urge to tweak the fill valve higher in search of a "stronger" flush; you'll just waste water and risk overflow.
Common Problems and Everyday Maintenance
Never drop bleach tablets or chlorine pucks into the tank of an Aquasource Henshaw. Tank additives shorten the life of the flapper, gasket, and fill valve seals dramatically, and they're one of the top causes of premature toilet failure. If you want to freshen the bowl, use a mild liquid cleaner and a brush. Clean the exterior with warm water and a soft cloth, and avoid abrasive pads that dull the glaze on the comfort-height rim.
Once or twice a year, check the supply line for cracking, look for moisture around the base, and listen for the sound of water running when no one is using the bathroom. Replace the flapper every three to five years and the supply line every five to eight. If you ever need to pull the toilet again, for a floor remodel or a stubborn clog, buy a new wax ring and start the sealing process from scratch. Wax seals are single-use items, full stop.
Installation is one of those jobs that rewards patience more than skill, and an Aquasource Henshaw gives you a forgiving canvas to learn on. Take your time with the flange, don't overtighten anything made of porcelain, and test before you caulk. Once the silicone cures and that first flush whooshes down clean and quiet, you'll have a bathroom fixture that should serve your household for a decade or more with nothing more than an occasional flapper swap. If anything about the flange or the water supply looks questionable while you're in there, that's the moment to call a plumber, because fixing it now costs far less than fixing the floor later.