Andersen Window Screen Sizes: Your Complete Guide to a Perfect Fit
Replacing a torn or missing screen on an Andersen window can feel deceptively simple until you realize that the company does not publish a single universal size chart. Andersen builds windows across a wide range of product lines, and the screen that fits a 400 Series Tilt-Wash double-hung unit is not the same screen that fits an A-Series casement. Understanding Andersen window screen sizes means understanding how the company labels its windows, how screens are measured, and why two windows that look identical from across the room can require completely different screen frames.
What follows is a practical breakdown of how Andersen sizing actually works, from decoding the unit number stamped on the window frame to measuring a screen that has already been removed. Whether you are ordering a replacement online, matching a screen at a local dealer, or trying to figure out why the screen you bought does not quite snap into place, the details below will save you a return shipment and a frustrating afternoon.
How Andersen Approaches Window Screen Sizing
Unlike generic window screen manufacturers that sell by rough opening dimensions, Andersen ties its screens directly to the window unit itself. Every Andersen window carries a unit number, typically a four-digit code that describes the nominal width and height in feet and inches. A 3052, for example, is nominally 3 feet 0 inches wide by 5 feet 2 inches tall. That unit number is the key that unlocks the correct screen size for that specific window.
This system exists because Andersen screens are engineered to fit the window's frame profile, not just its opening. The screen frame has to clear the sash, seat properly against the screen channel, and in many cases accept specific retention hardware. A generic screen cut to the visible glass size will rarely fit correctly, which is why buying by brand and unit number matters far more than buying by measurement alone.
Why Andersen Uses Its Own Sizing System
Andersen has manufactured windows for more than a century, and over that time it has produced dozens of distinct product families, each with its own frame geometry. The 200 Series Narroline, 400 Series Tilt-Wash, 400 Series Woodwright, 100 Series, A-Series, and E-Series all use different screen attachment methods. Some screens press into a channel, some clip onto the exterior frame with spring-loaded retention, and some slide into a track shared with the sash.
Because those attachment systems differ, the outside dimensions of the screen frame differ too, even when the visible glass area is identical. Andersen therefore publishes screen sizing by product line and unit number rather than by a single measurement. If you own a 400 Series double-hung, you order a 400 Series double-hung screen in the matching unit size. That is the entire system in a nutshell.
The Difference Between Visible Glass and Screen Dimensions
A common mistake is measuring the visible glass area and assuming that is the screen size. It is not. The screen frame overlaps the window frame or sash, and it includes corners, splines, and retention clips that extend beyond the opening. Measuring the glass will almost always produce a screen that is too small and falls out of the channel.
Instead, if you must measure, measure the existing screen frame from outside edge to outside edge, then note the frame profile and the location of any retention hardware. If the original screen is gone, measure the screen channel or the sash opening and compare it to Andersen's published dimensions for your product line. When in doubt, the unit number is a more reliable guide than a tape measure.
Measuring and Identifying Your Andersen Screen Size
Before you can order anything, you need two pieces of information: the product line and the unit number. Both are usually printed on a label affixed to the window frame, often on the head jamb or the side jamb of the operable sash. On older windows the label may be faded or missing, in which case the unit number can sometimes be found etched into the glass or stamped on the sill.
Once you have that information, the ordering process becomes straightforward. Andersen dealers and online replacement-screen retailers cross-reference the unit number to a specific screen part number. That part number is what you actually need, because it encodes the product line, the size, and the hardware configuration all in one string.
Tools and Techniques for Accurate Measurement
If the label is unreadable or the window is a discontinued model, careful measurement is the fallback. Use a steel tape rather than a cloth one, and measure the screen opening at three points for width and three for height, recording the smallest figure each time. That accounts for any out-of-square framing that develops as a house settles.
Pay close attention to the depth of the screen channel and the presence of any stops or clips. A screen frame that is the right width and height but the wrong depth will not seat properly. Photograph the corners of the opening and the frame profile, because those images will help a dealer identify the correct replacement even without a legible unit number.
Decoding Andersen Unit Numbers and Screen Part Numbers
Andersen unit numbers follow a consistent logic across most product lines. The first two digits represent nominal width in feet and inches, and the last two represent nominal height. A 2846 is 2 feet 8 inches wide by 4 feet 6 inches tall. Special shapes and non-standard units use letter prefixes or suffixes that indicate the configuration.
Screen part numbers are a separate string, usually beginning with a prefix that identifies the product line, followed by a numeric code for the size and a suffix for the hardware. The table below shows a few representative conversions to illustrate how the two systems relate.
| Unit Number | Nominal Size | Typical Product Line |
|---|---|---|
| 2846 | 2'8" x 4'6" | 400 Series Double-Hung |
| 3052 | 3'0" x 5'2" | 400 Series Double-Hung |
| 3056 | 3'0" x 5'6" | 200 Series Narroline |
| 2646 | 2'6" x 4'6" | 100 Series Double-Hung |
These figures are nominal, not exact. The actual frame dimensions will differ slightly by product line, which is why the part number is the authoritative reference. Use the table as a cross-check, never as the sole basis for an order.
Matching Screens to Specific Andersen Product Lines
Andersen's product families each carry their own screen conventions, and mixing them up is the single most common reason a replacement screen gets returned. The 400 Series Tilt-Wash, for instance, uses a screen that engages the screen channel on the exterior of the window and is typically a full screen covering the entire unit opening. The 200 Series Narroline double-hung, by contrast, has a different channel depth and uses a slightly different frame thickness.
Casement and awning windows introduce another layer of variation. Their screens mount on the interior side of the window and are held by a frame that presses against the sash, which means the screen dimensions align with the interior opening rather than the exterior frame. A screen meant for a double-hung will not fit a casement of the same nominal unit size, even if the numbers match.
Standard Sizes Versus Custom and Specialty Shapes
Most rectangular Andersen windows in common unit sizes have off-the-shelf screen options available through dealers and third-party retailers. These standard screens ship quickly and are the most economical choice. They are stocked for popular sizes like 2846, 3052, and 3056, which appear in a huge percentage of residential installations.
Specialty shapes, including arch-tops, quarter-rounds, octagons, and trapezoids, generally require custom screens. Andersen produces these to order based on the unit number, and lead times are longer. Custom screens for specialty shapes are also more expensive, so it is worth confirming the unit number twice before submitting an order.
Where to Buy and What to Verify Before Ordering
Replacement Andersen screens are available directly through Andersen's dealer network, through large home improvement retailers, and through independent online screen suppliers. Each channel has trade-offs. Dealers offer the highest confidence in fit and can look up your unit number in the Andersen system, while online suppliers often beat dealer pricing but require you to supply the part number yourself.
Regardless of where you buy, verify four things before checkout: the product line, the unit number, the screen type (full or half), and the hardware configuration. Full screens cover the entire unit opening, while half screens cover only the operable sash on a double-hung. Ordering a half screen when you need a full one is an easy mistake and an easy one to avoid with a quick measurement of the original screen's height.
Get the unit number right, confirm the product line, and the rest of the process takes care of itself. Andersen has made screen replacement genuinely simple for anyone willing to spend five minutes reading the label on the window frame. Take that step first, and you will have the correct screen in hand long before the next storm season rolls through.