80 Amp Wire Size Chart: What Gauge Wire for 80 Amps?
Running an 80 amp circuit is a serious electrical project, and the wire you choose determines whether the installation runs cool and efficient for decades or overheats and fails within months. Unlike a standard 15 or 20 amp branch circuit, an 80 amp feeder carries enough current to power a subpanel, a large tankless water heater, a heavy-duty welder, or a shop full of equipment. Getting the wire gauge right is not a matter of preference; it is a matter of code compliance and physical safety.
This guide breaks down everything you need to know about 80 amp wire size, from the ampacity tables electricians use every day to the voltage drop math that determines whether you need to bump up a size for a long run. You will learn how copper and aluminum compare, why temperature ratings change the answer, and which mistakes inspectors see most often on 80 amp installations.
Understanding 80 Amp Wire Size and Ampacity Ratings
Ampacity is the maximum amount of current a conductor can carry continuously without exceeding its temperature rating and damaging its insulation. The National Electrical Code publishes these values in Table 310.16, and the table is organized into three temperature columns: 60°C, 75°C, and 90°C. An 80 amp circuit requires conductors with an ampacity of at least 80 amps, but which column you read from depends on the weakest link in the circuit — usually the terminals on the breaker or the equipment being fed.
This is where most DIYers get tripped up. A piece of 4 AWG copper THHN wire is rated for 95 amps at 90°C, yet the breaker lug it terminates on might only be rated for 75°C. In that case, you must use the 75°C value, which is 85 amps for 4 AWG copper. The conductor's true usable ampacity is always limited by the lowest temperature rating in the chain of connected components.
Why Temperature Ratings Change the Answer
Terminations, lugs, and breaker bodies are manufactured with specific temperature ratings, and the code requires you to size the conductor based on that rating. Most modern circuit breakers and panel lugs are rated for 75°C, which is why the 75°C column is the default reference for typical residential and light commercial work. Older equipment rated only for 60°C forces you to use a larger conductor for the same 80 amps.
As a practical example, an 80 amp feeder in a modern panel using 75°C terminations can be built with 4 AWG copper. The same feeder landing on older 60°C equipment would require 3 AWG copper, because 4 AWG copper only carries 70 amps in that column — ten amps short of what the circuit demands.
Copper Versus Aluminum Conductors
Aluminum wire has roughly 78 percent of the conductivity of copper, so it must be sized larger to carry the same current. The tradeoff is that aluminum costs significantly less, which makes it attractive for long feeders and service entrances. For an 80 amp circuit, aluminum generally requires two to three sizes larger than copper to reach the same ampacity.
If you go with aluminum, you must use lugs and terminals listed for aluminum conductors, and it is wise to apply an antioxidant compound at the terminations. Aluminum also expands and contracts more than copper with temperature swings, so proper torque with a calibrated torque wrench is not optional — loose aluminum terminations are a leading cause of overheating and arcing.
| Conductor | Ampacity at 60°C | Ampacity at 75°C |
|---|---|---|
| 4 AWG Copper | 70 A | 85 A |
| 3 AWG Copper | 85 A | 100 A |
| 2 AWG Aluminum | 75 A | 90 A |
| 1 AWG Aluminum | 85 A | 100 A |
Choosing the Right Gauge for Your Specific Run
Ampacity alone does not determine the final wire size. The length of the run introduces resistance, and resistance causes voltage to drop along the conductor. The code does not mandate a specific voltage drop limit for most feeders, but the industry standard is to keep the total drop under 3 percent for branch circuits and feeders, and under 5 percent for the combined feeder plus branch circuit.
That 3 percent target is why a wire size that works perfectly for a 40 foot run can fail on a 150 foot run. When voltage drops too far, motors run hotter, electronics behave erratically, and equipment operates below its rated performance. The fix is simple: increase the conductor size until the calculated drop falls within the acceptable range.
Short Runs and Standard Feeder Installations
For runs under roughly 50 feet, ampacity drives the decision and voltage drop is rarely an issue. A typical 80 amp subpanel feeder in this range can use 4 AWG copper THHN or 2 AWG aluminum XHHW, assuming 75°C terminations on both ends. If the wire is NM-B cable, however, you must use the 60°C column because of the cable's insulation system, which means 3 AWG copper becomes the minimum.
Consider a detached garage subpanel fed 30 feet from the main house panel. At that distance, 4 AWG copper in conduit handles 80 amps comfortably, and the voltage drop at 240 volts works out to well under 1 percent. This is the most economical and common configuration for an 80 amp feeder.
Long Runs and Voltage Drop Compensation
Once you pass about 100 feet, voltage drop starts to dominate the sizing decision. Using the standard formula VD = (2 × K × I × L) ÷ CM, where K is 12.9 for copper and 21.2 for aluminum, you can calculate the drop for any combination. For an 80 amp load at 240 volts over 150 feet, 4 AWG copper produces roughly 7.4 volts of drop — just over the 3 percent threshold.
Stepping up to 3 AWG copper reduces that drop to about 5.9 volts, or 2.4 percent, which brings the circuit back into compliance with good design practice. For very long runs of 200 feet or more, 2 AWG copper or 1/0 aluminum may be necessary. The cost of upsizing wire is far lower than the cost of replacing a burned-out motor or a failed piece of equipment.
Installation, Code Compliance, and Safety Details
Beyond wire size, an 80 amp circuit has several code requirements that affect how you install it. The overcurrent device must protect the conductor, meaning the breaker's rating cannot exceed the adjusted ampacity of the wire. Standard breaker sizes include 80 amps, so you do not need to round up to 90 or 100 amps — a dedicated 80 amp breaker is readily available.
Derating factors also come into play when conductors share a raceway. If you pull more than three current-carrying conductors through a single conduit, you must apply adjustment factors from Table 310.15(C)(1). A 4 AWG copper THHN conductor that starts at 95 amps in the 90°C column might drop to 76 amps after adjustment, which would disqualify it for an 80 amp circuit.
Breakers, Disconnects, and Termination Ratings
Every termination point in the circuit has a temperature rating, and the lowest one governs. Panel main lugs, breaker terminals, and equipment terminal blocks all need to be checked. In most modern residential panels, breakers are marked for 75°C conductors, so 4 AWG copper or 2 AWG aluminum satisfies an 80 amp feeder without issue.
If you are feeding a piece of equipment with 60°C terminations, you must either upsize the conductor or use a short length of larger wire as a transition. Many inspectors look specifically for this, so verify the rating label on the equipment before you buy wire.
Common Mistakes and Real-World Applications
One of the most frequent errors is treating an 80 amp circuit like a 100 amp circuit and using 4 AWG aluminum. At 75°C, 4 AWG aluminum is only rated for 65 amps, which is dangerously undersized for an 80 amp load. Another common mistake is ignoring the 60°C restriction on NM-B cable, resulting in a feeder that appears correct on paper but fails inspection.
In practice, 80 amp circuits show up in applications like EV charger subpanels, large tankless water heaters, welding outlets, and shop feeders for compressors and table saws. In each case, the correct answer depends on the conductor material, the termination temperature, the run length, and the installation method — four variables that together determine the final wire gauge.
Before you buy a single foot of wire, sketch out the full circuit path and measure the actual distance from the panel to the load. Then cross-reference your conductor type against Table 310.16, confirm the temperature rating of every termination, and run a quick voltage drop calculation. A wire gauge that satisfies all four checks will give you an 80 amp circuit that runs cool, passes inspection, and keeps your equipment running reliably for years.