4x4 Nominal Size Explained: Actual Dimensions, Uses & Buying Guide
A 4x4 is one of the most recognizable pieces of dimensional lumber on the shelf, but the label can be misleading if you assume it describes the exact measurements. Pick up a standard 4x4 from a home center or lumber yard, wrap a tape measure around it, and you will likely find a 3.5-inch by 3.5-inch square. That gap between the name and the actual size is the heart of what builders call the 4x4 nominal size, and understanding it is essential for framing, landscaping, furniture making, and any project where a fraction of an inch can make or break a fit.
Nominal sizing is not a trick or a marketing gimmick. It is a standardized trade convention that has evolved over decades to account for drying, planing, and the need for uniform building materials. Knowing how nominal sizes work helps you order the right lumber, design accurate plans, and avoid the frustration of discovering your “4-inch” post is actually half an inch smaller on every side.
What Does 4x4 Nominal Size Actually Mean?
In the lumber industry, a nominal size is the name of the product, not its finished dimensions. When you buy a 4x4, you are purchasing a piece of wood that started as a rough green timber measuring approximately 4 inches by 4 inches. After it is dried and surfaced, the final product shrinks and smooths down to a smaller actual size. For most softwood dimensional lumber, that means a 4x4 nominal size translates to an actual size of 3.5 inches by 3.5 inches.
This convention applies across the board for standard dimensional softwoods. A 2x4 is actually 1.5 inches by 3.5 inches, a 2x6 is 1.5 inches by 5.5 inches, and a 4x4 follows the same pattern. The nominal size is what you use when talking to suppliers, reading span tables, or following building codes. The actual size is what you use when measuring for cuts, clearances, and finishes.
Nominal vs. Actual Dimensions
The difference between nominal and actual dimensions is consistent for most softwood lumber: roughly half an inch is removed from each dimension during processing. For a 4x4, that means 4 inches becomes 3.5 inches. This is true for pine, fir, spruce, hem-fir, and most pressure-treated lumber sold in big-box stores and traditional lumber yards. However, there are exceptions. Rough-sawn 4x4s, often used in timber framing, may be a full 4 inches by 4 inches because they are not planed smooth. Hardwood 4x4s can also vary depending on whether they are sold rough, surfaced two sides, or surfaced four sides.
Consider a practical example. You are building a pergola and want four visible posts that look like true 4-inch squares. If you buy standard 4x4 nominal lumber, your posts will be 3.5 inches square. That might be perfectly fine, but if your design calls for a chunky, heavy look, you may need to step up to a 6x6 nominal post, which actually measures 5.5 inches by 5.5 inches. Alternatively, you could order rough-sawn 4x4s or mill your own posts from larger stock. The key is to decide based on actual dimensions, not the nominal label.
Why the Dimensions Shrink
Two main forces turn a rough 4x4 into a finished 3.5x3.5: planing and drying. When a log is first sawn, the lumber is rough and green, meaning it has a high moisture content. Before it can be sold as dimensional lumber, it is dried in a kiln or air-dried to a lower moisture content. As the wood loses moisture, it shrinks. After drying, the rough lumber is run through a planer to create smooth, uniform faces and edges. The planer removes additional material, and the combination of shrinkage and planing produces the final actual size.
Industry standards, such as the American Softwood Lumber Standard (PS 20), set the rules for these dimensions so that builders can rely on consistent sizes across suppliers. Moisture content still matters, though. Kiln-dried lumber is more stable and less likely to shrink further after installation. Green or treated lumber may continue to dry and move slightly, which can affect tight joints and finishes. Hardwoods follow different grading and surfacing rules, often sold in quarters like 4/4 or 8/4, and their actual dimensions depend on how much surfacing is done.
Using and Buying 4x4 Nominal Lumber
A 4x4 is a versatile workhorse in construction and woodworking. You will find it in deck posts, fence posts, pergolas, barn framing, furniture legs, garden bed borders, and temporary shoring. Because it is square and relatively easy to handle, it works well for both structural and decorative applications. But to use it effectively, you need to plan around its actual size and understand how nominal sizing affects everything from hardware selection to load capacity.
When you shop for 4x4 lumber, you will encounter different species, grades, treatments, and moisture levels. Each of these factors influences strength, durability, appearance, and cost. A pressure-treated 4x4 for a ground-contact fence post is a very different product from a kiln-dried cedar 4x4 for an indoor furniture project. Knowing what you need before you buy saves time and prevents costly returns.
Structural and Outdoor Applications
In structural and outdoor projects, 4x4 nominal posts are commonly used for deck railings, pergola uprights, fence posts, and light-duty support columns. The actual 3.5-inch square size fits standard post bases, caps, and connectors that are designed for nominal 4x4 lumber. For example, a typical post base for a 4x4 will have an opening or adjustable straps sized to accept a 3.5-inch post. If you substitute a rough-sawn 4x4 that is a full 4 inches, you may need to modify the hardware or choose a different connector.
For structural loads, always check local building codes and span tables. A 4x4 post has limited load-bearing capacity compared to a 6x6, especially when used as a column. In many deck designs, 6x6 posts are required for the main support, while 4x4 posts are used for railings and above-deck features. For outdoor ground contact, choose lumber rated for ground contact, such as UC4A or UC4B pressure treatment. Cedar and redwood are naturally rot-resistant but may be sold in nominal sizes that are slightly different from treated pine, so verify actual dimensions before framing.
Species, Grades, and Buying Tips
Softwood 4x4s are typically made from pine, fir, spruce, or hem-fir. Common grades include No. 2, No. 1, and Select Structural. No. 2 is the most common for general construction and allows knots and minor defects, while higher grades have fewer knots and greater strength. Hardwood 4x4s, such as oak or maple, are often sold rough-sawn or surfaced on two sides. A rough hardwood 4x4 may be a true 4 inches square, while a surfaced version could be 3.5 inches or slightly different depending on the mill.
When buying, bring a tape measure and check the actual dimensions, especially if you are matching existing lumber or fitting hardware. Inspect each piece for straightness, large knots, cracks, and signs of warping. For treated lumber, look at the end tag to confirm the retention level and intended use. Store lumber flat and supported off the ground to prevent bowing. When cutting treated wood, wear a dust mask and gloves, and pre-drill holes for screws or bolts to reduce splitting. These small steps make a big difference in the quality and longevity of your finished project.
So the next time you pick up a 4x4, don’t be surprised when your tape measure reads 3.5 inches. That difference is the legacy of a system built around stable, uniform, and workable lumber. Whether you are framing a deck, setting a fence post, or building a piece of furniture, design with the actual dimensions in mind. Your projects will fit better, last longer, and look more professional because you understood the 4x4 nominal size before you made the first cut.