42RE Transmission Parts Diagram: Complete Illustrated Guide for Repair & Rebuild
Rebuilding or repairing a Chrysler-designed 42RE automatic transmission is far easier when you have a clear, accurate parts diagram in front of you. This four-speed overdrive unit, used behind the 4.0L inline-six and several V8 applications in Jeep Grand Cherokee, Dodge Dakota, Durango, and Ram models, packs a surprising amount of hardware into a compact case. Trying to reassemble one from memory alone is a recipe for misplaced check balls, reversed clutch plates, and a transmission that never shifts out of second gear.
A proper exploded view diagram solves most of that guesswork. It shows you how the castings stack together, which way the clutch steels face, where the thrust washers land, and how the valve body hardware is sequenced. The goal here is to walk you through what a 42RE transmission parts diagram actually contains, how to read the callout numbers, and which assemblies deserve the closest attention when you tear into the unit.
Understanding the 42RE Transmission Layout
The 42RE belongs to the Torqueflite-derived family that includes the 44RE, 46RE, and 47RE. It is a four-speed automatic with a hydraulically shifted main case and an electronically controlled overdrive section bolted to the rear. That split personality is the single most important thing to understand before you open a diagram, because the front half of the unit and the rear overdrive housing use completely different logic and different part groups.
When you look at a well-made parts diagram, the illustration is almost always divided along those lines. The front section covers the torque converter, oil pump, input shaft, front and rear clutch packs, bands, and planetary gear sets. The rear section covers the overdrive planetary, the overdrive and direct clutch packs inside the overdrive housing, the overrunning clutch, and the extension or tail housing that carries the output shaft and speed sensors.
Major Castings and Housings
Castings are the easiest parts to identify on a diagram and the ones most often damaged by neglect. The bell housing, main case, valve body, overdrive housing, and extension housing are all numbered separately, and the diagram will typically show bolt locations, dowel pins, and locating bosses so you can see exactly how each piece registers to the next. Pay attention to the pump housing as well, since it doubles as the front seal carrier and must mate squarely with the case.
In the real world, the most common casting failures are cracked extension housings from driveline vibration, worn pump stator support bushings, and stripped threads at the valve body mounting bosses. A diagram will not tell you a thread is stripped, but it will show you how many fasteners belong in each location, which lets you spot a missing bolt or a mismatched-length replacement before the unit goes back in the vehicle.
Hydraulic and Electronic Control Components
The valve body is where a 42RE diagram earns its keep. Exploded views of the valve body show the separator plate, the upper and lower valve body halves, the accumulator pistons and springs, the manual valve, shift valves, and every check ball in its proper pocket. The solenoid pack mounts to the valve body and controls overdrive and torque converter lockup, while the governor pressure solenoid and governor pressure sensor sit on the rear of the case and feed shift timing information to the control module.
Because there are multiple revisions across the production run, you should always match the diagram to your specific model year and engine rather than assuming any 42RE view will do. Valve body calibrations, solenoid connector styles, and separator plate orifice sizes changed over the years, and using the wrong diagram can send you chasing a shift complaint that was never a mechanical fault to begin with.
| Assembly Group | Typical Diagram Callouts | Primary Wear Points |
|---|---|---|
| Pump and Converter | Converter, pump body, stator support, front seal | Bushing wear, seal leaks, converter clutch failure |
| Clutch and Band Section | Front clutch, rear clutch, bands, drums, pistons | Burned frictions, hardened seals, warped steels |
| Gear Train | Planetaries, sun gear, output shaft, thrust washers | Gear tooth damage, end play out of spec |
| Control Section | Valve body, solenoid pack, governor, sensors | Sticking valves, debris, electrical faults |
| Overdrive Housing | Overdrive clutch, direct clutch, overrunning clutch | Clutch burn-up, bearing noise, seal leaks |
Reading a 42RE Parts Diagram for a Rebuild
Diagrams are only useful if you know the order in which to read them. The trick is to work from the outside in and from the input to the output, following the power flow rather than jumping between unrelated assemblies. Start at the converter, move through the pump and input shaft, then progress rearward through the clutch packs, gear sets, valve body, and finally the overdrive section.
It also helps to treat every diagram number as a purchase decision, not just a reference. If callout 27 is a thrust washer, you need to know whether it is a selectable thickness washer that sets end play or a fixed-dimension part. Diagrams that include a legend with part names and quantities save you from ordering a single snap ring when the job actually calls for three of them.
Torque Converter, Pump, and Input Section
The front of the diagram usually shows the torque converter, flexplate bolts, converter hub, and the pump assembly that the hub drives through machined flats. The pump contains a crescent-style gear set, a pressure regulator valve, and a boost valve, and each of those pieces has a specific orientation that the exploded view makes obvious. Installing a pump gear backwards is a mistake that costs an entire rebuild.
This is also where you will find the input shaft, the forward and direct clutch apply pistons, and the sealing rings that route hydraulic pressure into the rotating drums. Inspect every sealing ring groove shown in the diagram, because a single cut ring can cause a pressure loss that mimics a failing clutch pack. If the diagram shows a specific stacking order for the return spring and retainer, follow it exactly and compress the assembly evenly with the correct tool.
Clutch Packs, Bands, and Overdrive Unit
The clutch section of the diagram shows frictions, steels, pressure plates, snap rings, wave plates, and return springs for each drum. Counting the plates and noting their order matters more than most first-time rebuilders expect, since an extra steel or a missing wave plate changes the clutch clearance and the apply feel. The front and rear bands appear alongside their struts, anchors, and adjusters, which makes it easy to confirm that the band lining faces the correct drum surface.
The overdrive housing is the last major group in the power flow and often the least understood. Its diagram typically shows the overdrive planetary, the overdrive clutch pack, the direct clutch pack, the overrunning clutch, and the small bearing and seal set that supports the output shaft. Because the overdrive section engages for fourth gear and for converter lockup strategy, worn components here usually show up as a no-fourth-gear complaint, a flare on the 3-4 shift, or a shudder at highway speed.
Parts Sourcing and Diagram Verification
Once you have identified the components you need, verify each part number against a source that accounts for year, engine, and driveline configuration. Two 42RE units from different model years can look identical on the outside while using different valve body calibrations, different sensor connectors, and different clutch friction materials. Cross-referencing the diagram against a VIN-specific parts catalog prevents the frustrating scenario of a fresh rebuild that will not shift correctly.
It is also worth keeping the diagram on hand during the teardown, not just the assembly. Laying each component on a bench in the exact order it appears in the illustration gives you a visual checklist and makes it immediately clear when a thrust washer, check ball, or snap ring has gone missing. Photograph each stage as you disassemble, and you will have a personal diagram that is specific to your exact unit.
The 42RE has a long production history and a strong aftermarket following, which means quality diagrams, rebuild kits, and upgraded hard parts are readily available. Take the time to find the correct exploded view for your application, study the callouts before you pick up a wrench, and the rebuild becomes a methodical process rather than a puzzle. Your transmission will reward that patience with clean shifts for a long time to come.