4/0-4/0-2/0 Aluminum URD Cable: Specs, Uses & Buying Guide
If you are planning an underground electrical service for a home, shop, or light commercial building, you have likely encountered the specification 4/0-4/0-2/0 aluminum URD. This cable assembly is a workhorse in residential underground distribution, delivering two large phase conductors and a reduced neutral in a single, direct-burial-ready package. Understanding what those numbers mean, where the cable is approved, and how to install it correctly can save you time, inspection headaches, and expensive rework.
Aluminum URD cable has become the default choice for many utility and contractor installations because it balances cost, weight, and electrical performance. The 4/0-4/0-2/0 configuration is especially common for 200-amp residential services, where two 4/0 aluminum conductors carry the main load and a 2/0 aluminum neutral handles the unbalanced return current. Below is a practical guide to sizing, code considerations, installation, and termination for this specific cable.
Understanding the 4/0-4/0-2/0 Aluminum URD Construction
URD stands for Underground Residential Distribution. It is a family of cables designed to be buried directly in the earth without a continuous conduit, although conduit sleeves are often used for physical protection at risers and transitions. A 4/0-4/0-2/0 aluminum URD assembly is typically a triplexed cable: two insulated 4/0 AWG aluminum phase conductors twisted around one 2/0 AWG aluminum neutral. The phase conductors are insulated with cross-linked polyethylene (XLPE) or a similar moisture-resistant compound, while the neutral may be bare or covered with a thin jacket for identification.
The numbers in the name are AWG sizes, not voltage ratings or ampacity values. The first two 4/0 values refer to the phase conductors, and the final 2/0 value refers to the neutral. Because the neutral in a 120/240-volt single-phase service only carries the imbalance between the two hot legs, it can often be smaller than the phase conductors. That is why a 4/0-4/0-2/0 cable can support a 200-amp service even though the neutral is two sizes smaller than the phase conductors.
What the 4/0, 4/0, and 2/0 Designations Mean
4/0 AWG is pronounced “four aught” and has a nominal area of 211,600 circular mils, while 2/0 AWG has 133,100 circular mils. In a 4/0-4/0-2/0 assembly, the first two numbers describe the ungrounded (hot) phase conductors, and the third number describes the grounded neutral. The phase conductors are significantly larger than the neutral because they carry the full load current, while the neutral carries only the unbalanced current in a typical 120/240-volt single-phase system. In triplex URD cable, the neutral is often bare stranded aluminum, and the phase conductors are usually black and red or black with a red stripe for identification.
For example, a 200-amp residential service with a 120/240-volt single-phase supply will use two 4/0 aluminum phase conductors to carry the full 200 amps to the panel. The 2/0 neutral returns only the difference between the two hot legs, which is rarely more than a fraction of the total load in a balanced panel. This is why the reduced neutral is acceptable under many code interpretations, provided the calculated maximum unbalanced load does not exceed the neutral ampacity. Always verify with your local authority having jurisdiction (AHJ) and utility requirements before assuming a reduced neutral is allowed.
Why Aluminum Is the Standard for URD Cable
Aluminum has roughly 61 percent of the conductivity of copper by volume, but it is much lighter and significantly less expensive. For large underground feeders like 4/0-4/0-2/0 URD, that cost difference can be substantial, especially when hundreds of feet are required. Modern aluminum conductors are made from AA-8000 series alloys, which have improved flexibility, creep resistance, and termination performance compared to the older, problematic aluminum conductors of the past.
Aluminum also forms a natural oxide layer that resists corrosion, but that same oxide layer is a poor conductor if it is not removed or penetrated during termination. That is why proper installation requires wire brushing, antioxidant compound, and connectors listed for aluminum. When installed correctly, aluminum URD cable delivers reliable performance for decades. Many utilities prefer it for secondary underground distribution because it is easier to handle in long runs and less attractive to thieves than copper.
Sizing, Ampacity, and Code Considerations for 4/0-4/0-2/0 Aluminum URD
Before you buy or bury 4/0-4/0-2/0 aluminum URD, you need to confirm that it meets the ampacity, voltage drop, and code requirements of your specific project. Ampacity is not a single fixed number; it depends on the conductor insulation temperature rating, the installation method, soil conditions, ambient temperature, and the number of current-carrying conductors in the trench. The National Electrical Code (NEC) provides baseline tables, but direct-buried URD cable often has its own listing and ampacity data from the manufacturer.
For a typical 4/0 aluminum conductor with 90°C XLPE insulation, the NEC ampacity in a raceway or cable is around 205 amps. In direct burial applications, the surrounding earth helps dissipate heat, so the allowable ampacity can be higher, sometimes in the 230- to 260-amp range depending on soil thermal resistivity and burial depth. However, the terminations, panel lugs, and service equipment may be rated for 75°C, which can limit the final ampacity to the 75°C column. A 4/0-4/0-2/0 URD is commonly used for 200-amp services, which provides a comfortable margin when voltage drop is not excessive.
Ampacity Ratings and Service Size
When sizing a 4/0-4/0-2/0 aluminum URD for a residential service, the most common target is 200 amps. At 75°C termination ratings, 4/0 aluminum is typically listed at 180 amps, which is slightly below 200 amps. However, service conductors are often sized under the NEC’s service-entrance rules, and the utility may have its own ampacity tables that allow 4/0 aluminum for 200-amp residential services. The key is to coordinate the cable ampacity with the service disconnect, meter socket, and panel bus rating. If the lugs are rated for 90°C, the conductor’s higher ampacity may be usable, but many inspectors still apply the 75°C limit.
For a 200-amp service, a 4/0-4/0-2/0 aluminum URD is often the minimum practical size for runs up to about 150 to 180 feet at 240 volts, depending on the acceptable voltage drop. If the run is longer, you may need to increase to 250 kcmil or parallel a second set. For a 150-amp service, 4/0-4/0-2/0 is more than adequate. For a 320-amp continuous service, this cable is generally too small unless it is paralleled or used with a larger neutral and proper overcurrent protection. Always perform a load calculation and a voltage drop calculation before finalizing the size.
Voltage Drop and Long Underground Runs
Voltage drop is often the deciding factor on long underground services. A 4/0 aluminum conductor has a resistance of roughly 0.101 ohms per 1,000 feet at 75°C, while a 2/0 aluminum neutral has about 0.160 ohms per 1,000 feet. In a 120/240-volt single-phase system, the voltage drop is calculated using the round-trip length of the phase and neutral conductors. For a balanced 200-amp load, the neutral current is low, so the phase conductors dominate the voltage drop. A 200-foot run of 4/0 aluminum at 200 amps can produce roughly 8 volts of drop, which is about 3.3 percent of 240 volts. That is close to the recommended 3 percent maximum for feeders, so longer runs may require a larger conductor.
To reduce voltage drop, you can increase conductor size, reduce the load, or shorten the run. For example, moving from 4/0 to 250 kcmil aluminum lowers resistance and can extend the allowable distance by roughly 15 to 20 percent. If the neutral is also carrying significant unbalanced load, the 2/0 neutral resistance can add to the drop, but in a well-balanced 120/240-volt panel, this effect is usually minor. A qualified electrician should perform the calculation using the actual load profile and the manufacturer’s resistance data.
Installation and Termination Best Practices for 4/0-4/0-2/0 Aluminum URD
Installing 4/0-4/0-2/0 aluminum URD correctly is just as important as selecting the right size. Because the cable is direct burial rated, it must be installed at the proper depth, protected from physical damage, and terminated with materials compatible with aluminum. Poor installation can lead to insulation damage, corrosion, loose connections, and premature failure. The following practices are widely accepted by electricians and inspectors, but always follow the NEC, local amendments, and the utility’s service requirements.
Before digging, confirm the trench depth. The NEC generally requires a minimum of 24 inches of cover for direct-buried service conductors, 18 inches under a concrete slab or driveway, and 12 inches under a building or concrete slab that is at least 2 inches thick. Some utilities require deeper trenches. Use sand or fine-grain soil as backfill around the cable, and install a warning tape or tracer wire above the cable to reduce the risk of future excavation damage. Keep the cable away from sharp rocks, roots, and debris that could abrade the insulation.
Direct Burial and Physical Protection
Although 4/0-4/0-2/0 aluminum URD is listed for direct burial, it still needs physical protection where it emerges from the ground. Use a rigid metal conduit, PVC conduit, or approved riser sleeve to protect the cable from lawnmowers, weed trimmers, and physical impact. The conduit should extend at least 8 feet above grade at the meter or service panel, and the cable should be secured and sealed to prevent moisture from entering the conduit. If the cable transitions from direct burial to conduit, use a bushing or bell end to prevent insulation damage.
When backfilling, do not use heavy machinery directly over the cable. Compact the soil in lifts and avoid dropping large rocks on the cable. If the trench crosses under a driveway, consider installing the cable in conduit for the crossing and increasing the burial depth to 18 inches or more. Always leave a few feet of slack at both ends for termination and future repairs. Before energizing, perform an insulation resistance test with a megohmmeter to confirm that the cable was not damaged during installation.
Terminations, Lugs, and Corrosion Control
Aluminum conductors require special termination attention. Use lugs and connectors that are listed for aluminum or dual-rated for copper and aluminum. Clean the conductor strands with a wire brush to remove the oxide layer, then apply an antioxidant compound rated for aluminum. Insert the conductor fully into the lug and torque the set screw or bolt to the manufacturer’s specification. Do not over-torque, as this can damage the strands, and do not under-torque, as this can lead to overheating. After termination, cover the lug with a heat-shrink or cold-shrink sleeve if it is exposed to weather or buried.
For direct burial splices, use only splice kits rated for direct burial and for the conductor size and material. The 2/0 neutral may be bare, so it must be identified and terminated with the same care as the phase conductors. If the neutral is bare and in contact with soil, use a splice kit that is compatible with direct burial and corrosion. Inside the panel, separate aluminum and copper conductors with appropriate barriers or use dual-rated lugs. Finally, re-check torque after the first load cycle, as aluminum can cold-flow and loosen slightly under initial thermal expansion.
Choosing 4/0-4/0-2/0 aluminum URD is a practical decision for many 200-amp underground residential services, but it is not a one-size-fits-all answer. Verify the ampacity, voltage drop, neutral sizing, and local code requirements before you order the cable. With proper trenching, protection, and aluminum-rated terminations, this cable can deliver dependable service for decades. If you are unsure about any part of the installation, bring in a licensed electrician or consult your utility early so your project passes inspection the first time.