200 Amp Service Cable: The Complete Guide to Sizing, Types, and Installation
When a home needs more power for modern appliances, electric vehicles, or a new addition, upgrading to a 200 amp service cable is often the first step. This cable carries electricity from the utility meter to the main breaker panel, and it must be sized, rated, and installed correctly to handle the load safely. A 200 amp service provides roughly twice the capacity of an older 100 amp service, making it a common choice for new construction and major renovations.
The term 200 amp service cable can refer to several products, including SEU, SER, and individual conductors run in conduit. The right choice depends on whether the service is overhead or underground, the distance from the meter to the panel, and the local electrical code. Getting this detail wrong can lead to overheating, nuisance tripping, failed inspections, or a dangerous electrical fire.
What Is a 200 Amp Service Cable?
A 200 amp service cable is a set of conductors designed to supply a 200 amp electrical service. It typically contains two hot conductors, one neutral conductor, and sometimes a grounding conductor, depending on the cable type. The cable is rated for the voltage and current of the service, and it must be listed for the application, such as service entrance or feeder use.
In residential systems, the service cable connects the utility's service drop or lateral to the main service panel. It must be protected from physical damage and installed according to the National Electrical Code (NEC) and local amendments. The cable's ampacity, insulation type, and temperature rating all play a role in whether it can legally and safely carry 200 amps.
Service Entrance Cable Types: SEU vs. SER
SEU cable, a common service entrance cable style, is often used for overhead service entrances. It has two insulated conductors and one bare concentric neutral, which also serves as the grounding conductor. For a 200 amp service, SEU cable is often sized as 2/0 copper or 4/0 aluminum, depending on the ampacity table and the 83% residential service rule.
SER cable is a round, jacketed cable with three insulated conductors plus a bare grounding conductor. It is used for service entrances, subpanel feeders, and other applications where a separate neutral and ground are required. A typical 200 amp SER cable might be 4/0-4/0-4/0-2/0 aluminum or 2/0-2/0-2/0-1 copper. Because SER has a full-sized neutral and separate ground, it is versatile but often more expensive than SEU.
Copper vs. Aluminum Conductors
Copper and aluminum are both acceptable for 200 amp service cable when the conductors and terminations are rated for the material. Copper has higher conductivity, so it requires a smaller wire gauge for the same ampacity. For example, 2/0 copper can often handle a 200 amp residential service, while aluminum typically requires 4/0. Copper is heavier, more expensive, and less prone to termination issues, but it is also a target for theft.
Aluminum is lighter, less expensive, and easier to bend, which makes it popular for large service cables. Modern aluminum conductors use alloys that reduce expansion and creep, but they still require antioxidant compound and proper torque at terminations. Always use lugs listed for aluminum or copper-aluminum, and never mix materials without a listed connector. Local codes and the inspector's preference may influence the final choice.
How to Size 200 Amp Service Cable Correctly
Sizing a 200 amp service cable starts with the load calculation. The NEC provides methods to determine the minimum service size for a dwelling, and a 200 amp service is often selected to provide headroom for future loads. Once the service size is confirmed, the conductor size is chosen based on ampacity, temperature rating, and the conditions of installation.
The common mistake is assuming that any cable labeled 200 amp is correct. Ampacity depends on the insulation rating, the number of current-carrying conductors, the ambient temperature, and the terminations. The cable must also be protected by a breaker or fuse that does not exceed the conductor's ampacity, except where the NEC allows the next standard size up.
Wire Gauge and Ampacity for 200 Amp Service
For a 200 amp residential service, the NEC's 83% rule often allows conductors with an ampacity of at least 166 amps. At 75°C, 2/0 copper has an ampacity of 175 amps, and 4/0 aluminum has an ampacity of 180 amps. These sizes are commonly used for 200 amp service cable in SEU and SER assemblies. If the application does not qualify for the 83% rule, 3/0 copper or 250 kcmil aluminum may be required.
Ampacity tables are not the only consideration. Terminations are typically rated for 75°C, even if the cable insulation is rated for 90°C. This means the 90°C column cannot be used unless the terminations are also rated for 90°C. In practice, most residential 200 amp service cables are sized using the 75°C column, which is why 2/0 copper and 4/0 aluminum are so common.
Voltage Drop, Distance, and Installation Conditions
Voltage drop becomes important when the service cable run is long. A 200 amp load over a long distance can cause the voltage at the panel to sag, leading to dimming lights, overheating motors, and inefficient operation. The NEC recommends keeping voltage drop under 3% for branch circuits and under 5% for the entire system, though these are not always mandatory for service conductors.
For runs over 100 feet, it is often wise to upsize the conductors. For example, a 200 amp service with a 150-foot run might need 3/0 copper or 250 kcmil aluminum to keep voltage drop acceptable. Installation conditions also matter: cables in hot attics, bundled together, or buried in soil may have reduced ampacity. Always check the manufacturer's data and local code requirements before finalizing the size.
Before buying any 200 amp service cable, confirm the load calculation, the available utility voltage, and the inspection requirements in your area. A licensed electrician can help you match the cable type, conductor material, and wire gauge to your specific installation, ensuring the system is safe, code-compliant, and ready for the next generation of electrical demands.