1x6 Cedar Boards: Best Grades, Prices & Project Ideas
A 1x6 cedar board is one of those materials that quietly shows up everywhere — in the privacy fence behind your neighbor's yard, on the face of a cottage, lining a sauna bench, or framing the raised beds in a kitchen garden. It is light enough to carry under one arm, naturally resistant to rot, and takes a finish beautifully. That combination makes it a favorite for anyone building something outdoors that needs to look good for years without constant attention.
Still, buying cedar gets confusing fast. Nominal sizes do not match actual measurements, grades vary wildly in both price and appearance, and not every cedar species performs the same way in every climate. A 1x6 board sold as "cedar" at one yard may be dense, tightly grained Western Red Cedar, while a stack at another may be light, knotty, and best suited for a fence picket. This guide walks through what 1x6 cedar boards actually measure, which species and grades are worth your money, where they perform best, and how to fasten, finish, and maintain them so they last.
Understanding 1x6 Cedar Board Dimensions and Species
The first thing to understand about any 1x6 lumber, cedar included, is that the name describes a rough, pre-milled size rather than the board you carry home. A 1x6 cedar board begins life as a rough-cut piece one inch thick and six inches wide, then gets planed smooth on all four sides. Planing removes material from every face, so the finished board shrinks — and if the board is kiln-dried afterward, it shrinks a little more.
That shrinkage is predictable and standardized, which is actually good news for builders. It means you can order boards from different suppliers, in different regions, and still get the same consistent dimensions so your layout math works out. The trick is simply to design around actual dimensions rather than nominal ones, and to account for the small variances that occur naturally in any wood product.
Nominal Sizing vs. Actual Measurements
A surfaced 1x6 cedar board typically measures 3/4 inch thick by 5-1/2 inches wide. Rough-sawn cedar, which you may find at a specialty mill or sawyer, holds the full 1 inch by 6 inches because it has not been planed. Lengths are sold in the size you ask for: an 8-foot board really is 8 feet long, since length is not reduced by surfacing.
Here is a quick reference for the sizes you will run into most often:
- Nominal 1x6, surfaced four sides (S4S): 3/4" x 5-1/2"
- Nominal 1x6, rough sawn: 1" x 6"
- Nominal 5/4x6 decking, surfaced: 1" x 5-1/2"
- Common lengths: 6', 8', 10', 12', and 16'
- Weight of a surfaced 1x6x8 in Western Red Cedar: roughly 5 to 6 pounds
Those half inches add up fast on a big project. A fence built on 5-1/2-inch boards instead of 6-inch boards loses about half a foot of coverage for every twelve pickets, and a board-and-batten wall laid out on nominal width will drift out of alignment by the second course. Always plan your spacing and your material list around actual measurements.
Western Red Cedar, Northern White Cedar, and Aromatic Cedar
When most people say "cedar board," they mean Western Red Cedar. Grown in the Pacific Northwest and British Columbia, it is the gold standard for outdoor use thanks to natural extractives called thujaplicins that fungi and insects dislike. It is also unusually stable, meaning it swells and shrinks less than most softwoods as humidity changes, which keeps joints tight and paint from cracking. Its grain is straight, it works easily with hand tools, and it weathers to a soft silver-gray if left unfinished.
Northern White Cedar, common in the Great Lakes and Northeast, is lighter and softer but equally rot-resistant and traditional for shingles, sauna interiors, and boat ribs. Eastern Red Cedar, technically a juniper, is denser and more aromatic, with a reddish heartwood that makes it ideal for closet lining, chests, and fence posts. If you are buying 1x6 boards at a big box store, you are almost certainly buying Western Red Cedar — but it pays to read the label, because the species affects weight, workability, and how long the board holds up in ground contact.
Where 1x6 Cedar Boards Perform Best
Because cedar is lightweight, dimensionally stable, and naturally decay-resistant, 1x6 boards occupy a sweet spot between thin trim stock and heavy structural lumber. They are thick enough to hold a screw without splitting and to span modest distances without sagging, but thin enough to cut quickly with a miter saw and handle without help. That makes them genuinely versatile rather than a single-purpose material.
The key is matching the board to the job. A 1x6 is an excellent picket, panel, and surface board. It is a poor choice for a deck joist, a structural header, or anything that needs to carry significant load. Understanding that distinction keeps projects both safe and cost-effective, since you never want to pay cedar prices for lumber that is going to be hidden inside a wall or buried in a footing.
Fencing, Privacy Screens, and Gates
Fencing is the single most common use for 1x6 cedar boards. The 5-1/2-inch actual width gives you clean, substantial pickets that block sightlines better than thinner stock, and cedar's rot resistance means the bottoms of those pickets will not crumble after a few wet seasons the way untreated pine would. A standard privacy fence built from 1x6 boards set with a small gap handles wind load well and looks far more substantial than thinner, cheaper alternatives.
For a typical 6-foot privacy fence, you will use three horizontal rails per section and roughly twenty pickets per eight-foot bay, depending on the gap you leave between boards. Set them with an 1/8-inch space in humid climates so swelling boards do not buckle against each other, and tighter in dry climates for maximum privacy. Cedar gates also benefit from 1x6 stock: build a rigid frame from 2x4s or 2x6s, then clad it in 1x6 boards arranged vertically, diagonally, or in a herringbone pattern for a custom look.
Siding, Trim, and Garden Structures
Cedar 1x6 boards are traditional for board-and-batten siding, where wide boards are applied vertically and narrow battens cover the seams. The system sheds water well, allows the wall to dry, and creates the deep shadow lines that define so much rural and coastal architecture. Spacing boards at 12 to 16 inches on center with a 1x2 or 1x3 batten over each joint creates a wall that is both durable and visually rich.
Beyond siding, the same board works beautifully as fascia, soffit, skirting, and porch trim. Gardeners use 1x6 cedar to build raised beds eight to twelve inches deep by stacking two courses, and because cedar contains no chemical preservatives, it is a safe choice for growing vegetables and herbs. Planter boxes, cold frames, pergola slats, sandbox frames, and sauna benches round out the list — any place where a light, moisture-tolerant, attractive board is needed.
Choosing, Cutting, and Maintaining Cedar Boards
Two boards of the same nominal size can differ dramatically in price, and the difference almost always comes down to grade and knot structure. Learning to read a grade stamp and inspect a board face takes about five minutes and can save you a lot of money on a large order, or save your project from a board that cups, splits, or drops a knot a year after installation.
Once the boards are home, a few simple habits during cutting and fastening will prevent most of the problems people run into with cedar: splitting at the ends, extractive stains bleeding through paint, and fasteners that corrode and streak the wood. Cedar is forgiving, but it rewards a little care.
Grades, Appearance, and Budget
Cedar grades run from virtually flawless to highly rustic. Clear grades have almost no knots and command the highest prices; Select Tight Knot (STK) offers a moderate number of tight, sound knots and is the sweet spot for most fencing, siding, and trim work. Lower grades — often sold as #2, #3, or utility — contain larger knots and more defects, and they are fine for projects where appearance matters less but structural integrity still does.
Watch for loose knots, which can fall out and leave a hole that lets water into the wood. Also check for excessive wane (bark or rounded edges), split ends, and heavy checking. Expect to pay somewhere in the range of fifteen to forty dollars for a single 8-foot 1x6 cedar board depending on grade, species, and region, with clear grades at the top of that range. For a fence, buying STK in bulk is almost always the smarter move than paying a premium for clear boards no one will inspect from three feet away.
Fasteners, Finishing, and Long-Term Care
Cedar contains acids and extractives that corrode plain steel, electroplated galvanized fasteners, and aluminum. Use stainless steel screws — 304 for most climates, 316 for coastal salt air — or hot-dipped galvanized nails. Pre-drill pilot holes within an inch or two of board ends, because cedar splits easily there. If you are nailing by hand, blunt the nail tip slightly with a hammer to reduce splitting further.
Left bare, cedar weathers to a uniform silver-gray that many people love and that requires no maintenance beyond an occasional cleaning. If you want to preserve the warm reddish-brown color, apply a penetrating oil or semi-transparent stain with UV inhibitors rather than a film-forming varnish or solid paint, which traps moisture and peels. Clean weathered boards with a mild oxygen bleach solution and a soft brush, rinse thoroughly, and let them dry for a few days before recoating. A light sanding on cut ends and exposed edges helps finishes adhere and keeps the wood looking crisp.
Cedar is one of the few building materials that looks better as it ages, and a 1x6 board is arguably the most flexible format it comes in — small enough to handle alone, substantial enough to define a fence line or a wall. Inspect the boards before you buy, size your layout around actual dimensions, and spend a few extra dollars on stainless fasteners. Do that, and the project you build this season will still be standing square and true a decade from now, needing little more than a rinse with a garden hose.