18/2 Lamp Wire: The Complete Guide to Safe and Effective Wiring
18/2 lamp wire is the flexible two-conductor cord that powers many table lamps, floor lamps, pendant lights, and small household appliances. The “18” refers to 18 AWG (American Wire Gauge), while the “2” means there are two insulated conductors inside the outer jacket. That combination makes it small enough to route through tight lamp bases, yet strong enough for typical lighting loads when it is selected and installed correctly.
If you are rewiring a vintage lamp, building a custom fixture, or replacing a damaged cord, understanding the ratings and limitations of 18/2 lamp wire is essential. Not every 18/2 cord is the same. Insulation type, temperature rating, strand count, and plug compatibility all affect whether the wire is safe for your project.
Understanding 18/2 Lamp Wire Specifications
At first glance, 18/2 lamp wire looks like simple zip cord. In reality, it is an engineered assembly that must meet specific electrical and physical standards. The conductors are usually stranded copper, which allows the cord to bend repeatedly without breaking. The outer jacket may be PVC, rubber, or a thermoplastic elastomer, and the two conductors are often bonded together so they can be separated easily for termination.
The most common style for lamp cord is SPT-1, followed by SPT-2. SPT-1 has thinner insulation, while SPT-2 adds a thicker jacket for better abrasion resistance. Both are typically rated 300 volts and 105°C, though you should always confirm the markings printed on the wire itself. Other variants, such as SVT or SJT, are round and jacketed, and they may be used where a more durable cord is required.
Gauge, Ampacity, and Voltage Ratings
An 18 AWG conductor is not intended for high-current appliances. Depending on the insulation type, conductor count, and installation conditions, 18/2 lamp wire may be rated for roughly 6 to 10 amps. At 120 volts, that translates to a practical range of about 720 to 1,200 watts, but manufacturers often specify a lower limit for continuous use. For a single 100-watt bulb, the current draw is less than one amp, so 18/2 wire has plenty of headroom.
Voltage drop becomes a factor when the cord is very long or the load is close to the wire’s limit. For example, 18 AWG copper has about 6.4 ohms of resistance per 1,000 feet. A 20-foot cord carrying 6 amps would lose roughly 1.5 volts, which is usually acceptable for a lamp but not ideal for a sensitive device. If you need a run longer than 25 feet, consider 16/2 lamp wire or a heavier gauge.
Insulation Types and Temperature Ratings
Standard 18/2 lamp wire with PVC insulation is rated for 105°C, which is fine for LED and incandescent bulbs that are not in direct contact with the cord. However, halogen bulbs and high-wattage incandescent bulbs can generate much higher temperatures. If the wire touches the bulb or sits inside a confined metal shade, the insulation can soften, crack, or melt over time. In those cases, use high-temperature fixture wire, silicone leads, or fiberglass sleeves.
You can identify the insulation rating by reading the print on the cord. A typical marking might say “SPT-1 18 AWG 2/C 105°C 300V” or “SPT-2 18/2 105°C.” If the marking is missing, rubbed off, or unreadable, treat the wire as unknown and replace it. For any lamp that gets hot near the socket, choose a cord with a higher temperature rating or add a ceramic socket with heat-resistant leads.
Applications and Installation of 18/2 Lamp Wire
18/2 lamp wire is designed for flexible cord applications, not permanent in-wall wiring. It is commonly used for table lamps, floor lamps, pendant lights, holiday decorations, small fans, and low-power appliances. It should never be run through walls, ceilings, or floors as a substitute for NM-B or conduit wiring. It also should not be used for space heaters, microwaves, or other high-current devices.
Installing 18/2 lamp wire correctly involves more than connecting two wires. You need to maintain polarity, provide strain relief, protect the cord from sharp metal edges, and ensure that all connections are tight. A loose strand or reversed polarity can create a shock hazard or a short circuit. The following sections cover the key steps for safe rewiring and connector selection.
Rewiring a Lamp Safely
Before you begin, unplug the lamp and remove the bulb, shade, and any removable parts. Take a photo of the existing wiring so you can replicate the connections. Cut a length of 18/2 lamp wire that is long enough to reach the outlet with some slack, but not so long that it becomes a tripping hazard. Slide any strain relief bushing or grommet onto the cord before you strip the ends.
Separate the two conductors at the end of the cord. Strip about 1/2 inch of insulation from each conductor, and strip 1 to 2 inches of the outer jacket to expose them. Tie an Underwriters knot inside the lamp base or use a mechanical strain relief to prevent pulling on the terminals. Connect the ribbed conductor to the neutral terminal, which is usually silver, and the smooth conductor to the hot terminal, which is usually brass. For a polarized plug, the wide blade connects to the ribbed neutral wire.
Choosing Connectors, Plugs, and Strain Relief
Use plugs and sockets rated for 18 AWG wire. A molded plug is convenient, but a rewirable plug lets you shorten or replace the cord later. Polarized plugs are strongly recommended because they keep the neutral side consistent. If the lamp has a metal body and no ground wire, make sure the cord is in good condition and that no conductor can touch the metal housing. For added protection, use heat-shrink tubing over exposed connections.
Strain relief is critical. Without it, a tug on the cord can pull the conductors loose inside the socket or plug. Common options include an Underwriters knot, a rubber grommet, a bushing, or a cord grip. Choose the method that fits your lamp’s base and the diameter of your 18/2 lamp wire. If the cord passes through a metal hole, install a grommet to prevent the insulation from being cut.
Whether you are restoring a flea-market find or building a custom fixture from scratch, using the right 18/2 lamp wire and following safe wiring practices will make your project reliable for years. Keep a spool of quality SPT-1 or SPT-2 cord on hand, double-check polarity, and never rush the strain relief. Your lamps will not only look better—they will be safer every time you flip the switch.