"16"" concrete form tube"

16 Concrete Form Tube: Ultimate Guide for Stronger Concrete Piers

By Kevin Martin
AD

A 16" concrete form tube is one of the most practical products you can buy when a project calls for a round, load-bearing pier that has to stand up to serious weight. Whether you are setting posts for a raised deck, anchoring a carport, or building a freestanding pergola, the 16-inch diameter sits in a useful sweet spot: large enough to carry heavy structural loads, yet still manageable for one or two people working with bagged mix or a small ready-mix delivery.

Many homeowners and contractors arrive at this size only after outgrowing the 8-inch and 12-inch tubes used for fence posts and light footings. Once load calculations demand more bearing area or a thicker pier, the 16-inch tube becomes the logical next step. What follows is a practical breakdown of what these forms are made of, where they belong on a job site, how much concrete they swallow, and how to install one without ending up with a cracked, crooked, or honeycombed pier.

Understanding the 16-Inch Form Tube

A concrete form tube is a rigid cylindrical shell that holds wet concrete in a round shape until it cures hard enough to stand on its own. Most 16-inch tubes are spiral-wound from multiple plies of heavy kraft paper bonded with moisture-resistant adhesive, then coated on the inside and outside with a wax or polymer release layer. That coating is what keeps the paper from soaking up water from the mix and swelling, and it also makes stripping the tube far easier once the concrete has set.

AD
Porch Foundations: More Important Thank You Think
Porch Foundations: More Important Thank You Think
many pipes are stacked on top of each other in the middle of an industrial area
many pipes are stacked on top of each other in the middle of an industrial area
several large white pipes are lined up on the sand in front of blue sky and clouds
several large white pipes are lined up on the sand in front of blue sky and clouds

The 16-inch figure is a nominal inside diameter, meaning the finished pier measures roughly 16 inches across. Wall thickness typically runs between a quarter and a half inch depending on the manufacturer and the rated pour height. Some premium tubes add a plastic inner liner or a foil facing for a smoother finished surface, which matters when the pier will remain exposed rather than be buried or covered by framing.

Standard Dimensions and Material Construction

Lengths vary by brand, but 4-foot, 8-foot, and 12-foot tubes are the most widely stocked, with 16-foot sections available through special order in many regions. A full 16-inch diameter tube holds roughly 1.4 cubic feet of concrete per linear foot, which works out to about 0.052 cubic yards per foot. An 8-foot tube therefore needs approximately 11 cubic feet of concrete, or roughly 19 bags of 80-pound mix if you are mixing by hand.

several cement pipes stacked on top of each other in the sand and blue sky behind them
several cement pipes stacked on top of each other in the sand and blue sky behind them
several large concrete pipes are lined up in a row on the cement ground with blue sky in the background
several large concrete pipes are lined up in a row on the cement ground with blue sky in the background
concrete being poured onto the ground by a crane
concrete being poured onto the ground by a crane

Weight is the detail that catches most first-timers off guard. Cured concrete weighs around 145 pounds per cubic foot, so a single 8-foot-long, 16-inch pier tips the scales at roughly 1,600 pounds. That mass is exactly why these piers resist uplift and lateral movement so well, and it is also why you should never plan to move one after the pour. Set the tube where it belongs the first time.

Where 16-Inch Tubes Are Typically Used

Deck and porch piers are the most common application. A 16-inch diameter footing spreads load over a much larger soil area than a 10-inch or 12-inch tube, which helps on marginal soils and in frost-prone regions where code may require deeper, wider footings. Pergolas, gazebos, and heavy gate posts also benefit from the extra mass and stiffness.

AD

Beyond residential work, this diameter shows up in light commercial settings such as sign posts, car wash equipment pads, and small structural columns. It is also a favorite for post-frame buildings where a single wide pier can support a laminated column. If your plans or engineer specify a 16-inch round footing, the paper tube is almost always the cheapest and fastest way to form it.

pipes are lined up in the middle of a construction area with dirt on the ground
pipes are lined up in the middle of a construction area with dirt on the ground
Concrete Pipe
Concrete Pipe
large concrete pipes are lined up in rows and ready to be put into the ground
large concrete pipes are lined up in rows and ready to be put into the ground
several large pipes stacked on top of each other in front of a crane and blue sky
several large pipes stacked on top of each other in front of a crane and blue sky
Quikrete Quik-Tube Rigid Fiber 12'' x 4' Concrete Form Tube
Quikrete Quik-Tube Rigid Fiber 12'' x 4' Concrete Form Tube
two large black tires are stacked on top of each other in front of a building
two large black tires are stacked on top of each other in front of a building

How to Install a 16" Concrete Form Tube Correctly

Installing a large-diameter form is not complicated, but it is unforgiving of shortcuts. Three things ruin more 16-inch piers than anything else: an under-dug or loose hole, a tube that is not plumb, and a pour rate that is too fast for the form to handle. Address those three items and the rest of the job tends to take care of itself.

Plan the work so the tube is braced, the concrete is ordered or staged, and the finishing tools are on site before the first wheelbarrow gets dumped. Wet concrete waits for nobody, and a 16-inch pier can consume well over a cubic yard of material in a hurry if the tube is deep.

AD

Site Preparation and Footing Considerations

Start by confirming the required footing depth with your local building department, since frost depth and soil bearing capacity determine how deep the hole must go. Dig the hole at least four inches wider than the tube on all sides so you have room to work, and bell out the bottom if your design calls for a spread footing. Compact the soil at the base and place a few inches of gravel for drainage where the water table is high.

large stack of pipes sitting on top of each other
large stack of pipes sitting on top of each other
three cement pipes sitting on the ground
three cement pipes sitting on the ground
several large pipes are lined up on the ground near each other in an open area
several large pipes are lined up on the ground near each other in an open area
several large pipes are lined up on the ground
several large pipes are lined up on the ground

Set the tube in the hole and check plumb with a four-foot level in two directions, then brace it with stakes and 2x4s driven into undisturbed soil. A tube this large catches wind and will shift during the pour if it is not tied off. Also verify that the top of the tube sits at the correct elevation for your post base or anchor bolt, and mark that line clearly before any concrete arrives.

Pouring, Consolidating, and Stripping the Form

Large-diameter paper tubes are rated for a maximum pour rate, often expressed in feet of rise per hour. Exceeding that rating lets hydrostatic pressure bulge or burst the form, so pour in lifts and pause between them. Use a concrete vibrator or, at minimum, rod the mix thoroughly with a piece of rebar to eliminate air pockets along the tube wall, which is where voids and honeycombing love to hide.

AD

Once the concrete is placed, strike the top level with a screed and cover the pier with plastic if freezing weather is expected. Curing time depends on temperature and mix design, but most contractors wait at least 24 to 48 hours before removing stakes and braces, and longer before loading the pier. To strip the tube, cut it lengthwise with a utility knife and peel it away; leaving it in place is also acceptable underground, though above-grade tubes should generally be removed so the concrete can dry evenly.

Buying Guide and Cost Expectations

Prices for a 16-inch tube move with paper costs, shipping distance, and length, but as a general rule you should expect to pay noticeably more than you would for the same length in a 12-inch size. A single 8-foot tube in this diameter commonly lands somewhere in the range of a mid-tier power tool, and buying two or three at once rarely triggers a discount because these are bulky, low-margin items for most retailers.

Where the real budget swing happens is concrete, not cardboard. A 16-inch pier needs so much material that ready-mix delivery often beats bagged mix on both cost and labor, especially once you pass two piers or about 20 bags. Get quotes from at least two suppliers and ask about minimum-load charges, which can quietly add a few hundred dollars to a small pour.

Comparing Brands, Coatings, and Options

The major manufacturers all produce reliable spiral-wound tubes in this diameter, and the differences come down to coating quality, ply count, and whether a smooth-finish liner is included. Waxed tubes are the standard workhorse and strip cleanly, while plastic-lined versions produce a near-architectural surface that can be left exposed with minimal patching. Fiber tubes made from recycled material are another option, though they are typically sold in shorter lengths and can be harder to find locally.

Inspect any tube before you buy it. Look for crushed ends, delamination between plies, and damp spots that suggest the coating has failed. A tube that has been sitting outside in the rain on a lumber yard rack is a tube that may bulge or blow out under load. Also confirm the actual inside diameter with a tape measure, because nominal sizing and slight manufacturing variance both exist in this category.

Practical Tips and Common Mistakes to Avoid

Never pour a 16-inch pier without at least one piece of vertical rebar tied into the footing below. The mass alone resists compression, but reinforcement handles tension and cracking, and most inspectors will require it. Keep rebar at least two inches from the tube wall and use chairs or a small spacer to hold that clearance through the pour.

Another common error is underestimating bracing. A tall, narrow column of wet concrete generates substantial lateral pressure at the base, and paper tubes are designed to contain it only when they are plumb and supported. Finally, resist the urge to backfill against a green pier. Give the concrete time to reach adequate strength, then backfill in shallow lifts and compact carefully so you do not crack the top of the column.

If you take the time to dig a proper footing, brace the tube square and plumb, and pour at a controlled rate, a 16-inch form tube will give you a pier that outlasts the structure sitting on top of it. Before you break ground, check your local codes, sketch the layout, and order your concrete with a little margin, because a half-yard short is a very expensive mistake. A solid plan today means decades of a rock-steady deck, pergola, or post frame tomorrow.

AD