12 craftsman band saw

12 Craftsman Band Saw: Ultimate Review, Buying Guide & Top Picks

By Thomas Lewis
AD

For woodworkers who need tight curve cuts, occasional resawing, and a footprint that won't swallow the whole shop, the Craftsman 12-inch band saw has quietly become one of the most practical benchtop machines of the past four decades. Thousands of them are still running in garages, basements, and school shops, and they show up constantly on the used market at prices that make a new bandsaw look absurd. If you inherited one from a relative or you're scanning listings for a cheap entry point into bandsaw work, this is a machine that rewards a little patience with a surprising amount of capability.

This guide covers what the Craftsman 12-inch band saw actually does well, where it falls short, and how to coax accurate cuts out of it. We'll walk through specs, blade selection, setup, tuning, maintenance, and the breakdowns that commonly appear on older units so you can decide whether one belongs on your bench.

What the Craftsman 12-Inch Band Saw Actually Offers

Craftsman sold these saws in several generations, and the model numbers matter more than the badge on the front. The most widely discussed is the 113.24261 family, built for Sears by Emerson Electric, but you'll also encounter later variants with slightly different frames, motors, and tensioning hardware. Nearly all of them share the same basic layout: two wheels, a benchtop or light stand-mounted chassis, and a throat capacity of roughly twelve inches between the blade and the column.

AD
Craftsman 12-Inch Band Saw/Sander Model 113.24201 Owner's Manual
Craftsman 12-Inch Band Saw/Sander Model 113.24201 Owner's Manual
Band Saws for sale | eBay
Band Saws for sale | eBay
a blue machine sitting on top of a wooden table
a blue machine sitting on top of a wooden table

That twelve-inch throat is the headline feature. It's enough to handle scroll work on cabinet parts, cut curves in chair legs, and trim tenons without constantly fighting the frame the way you would on a nine- or ten-inch saw. Add a modest resaw capacity and you have a machine that covers an enormous range of small-shop tasks for a fraction of what a floor-standing 14-inch saw costs.

Key Specifications and Motor Performance

Most 12-inch Craftsman band saws run a 1/2-horsepower, 120-volt induction motor. That's not earth-shaking power, but it's honest power, and induction motors hold up far better than the universal motors found on some budget imports. Several vintages offer multiple blade speeds through a stepped pulley arrangement, letting you slow the blade for metal, plastics, or hard dense woods and speed it up for softwoods and quick rips.

The Best Craftsman 12 Inch Band Saw: Review in 2026 - The Saw Guy
The Best Craftsman 12 Inch Band Saw: Review in 2026 - The Saw Guy
Craftsman 12” Band Saw
Craftsman 12” Band Saw
Band Saws for sale | eBay
Band Saws for sale | eBay

Typical figures look like this, though exact numbers vary by model year and you should always confirm against your specific manual:

SpecificationTypical Range
Throat capacityAbout 12 inches
Maximum resaw heightRoughly 3-1/2 to 4-5/8 inches
Blade lengthUsually 80 inches
Blade widths supported1/8 inch to 1/2 inch
Motor1/2 HP, 120V induction
Table sizeApproximately 15 x 15 inches

In practice, that 1/2-horsepower motor means you can resaw softwoods and medium hardwoods at a reasonable pace with a sharp, coarse blade. Push a 4-inch slab of hard maple through with a dull blade and you'll stall it. Feed rate matters more on this saw than on a 1-1/2-horsepower machine, so let the teeth do the cutting instead of your forearms.

AD

Build Quality and Table Design

The table on most of these saws is cast iron or a heavy cast aluminum, which is a genuine advantage. Cast tables resist vibration, stay flat over decades, and give you a solid reference surface for sleds and fences. The trunnion under the table allows bevel cuts, and while the tilt mechanism isn't as slick as what you'd find on a modern European saw, it locks down and holds its angle once you set it.

a wheel that is attached to a blue ribbon on a white background, with the end of it being held by a metal spoole
a wheel that is attached to a blue ribbon on a white background, with the end of it being held by a metal spoole
ad eBay | $21.95 | Owner's Manual & Parts List Sears Craftsman 12" Band Saw - Model 137.224320 | Bu
ad eBay | $21.95 | Owner's Manual & Parts List Sears Craftsman 12" Band Saw - Model 137.224320 | Bu
an image of a metal object with screws and nuts on blue carpeted floor
an image of a metal object with screws and nuts on blue carpeted floor
Hoteche 12-Inch Band Saw 7-Amp Two-Speed Benchtop with Stand for Woodworking and Metal Cutting, 1HP
Hoteche 12-Inch Band Saw 7-Amp Two-Speed Benchtop with Stand for Woodworking and Metal Cutting, 1HP
Official Craftsman 113197731 radial arm saw Parts
Official Craftsman 113197731 radial arm saw Parts
ad eBay | $19.95 | Owner's Manual & Parts List Sears Craftsman 10" Band Saw - Model 351.214000 | Bu
ad eBay | $19.95 | Owner's Manual & Parts List Sears Craftsman 10" Band Saw - Model 351.214000 | Bu

Where these saws show their age is in the details. Guide bearings, blade tension springs, tires, and the plastic or thin-metal knobs are the parts that wear out or break. The good news is that most of those components are inexpensive and widely available. Replacing a tired tension spring and a set of urethane tires can transform a sluggish forty-year-old saw into something that cuts straight and holds tension all afternoon.

Setup, Blade Selection, and Tuning

A bandsaw is only as good as its setup, and this is where most Craftsman 12-inch machines get unfairly blamed for problems that come down to adjustment. Out of the box, or after years of neglect in someone's garage, the blade is usually tracking poorly, the guides are misaligned, and the tension is whatever it happened to be when the previous owner last touched it. Fixing those three things takes about half an hour.

AD

If you're buying used, budget for a new blade immediately. You have no idea what the previous owner was cutting, how hard they pushed it, or whether the blade picked up a kink. A fresh blade is the cheapest accuracy upgrade you can make, and it eliminates an entire category of variables before you start chasing alignment issues.

Photo Index - Sears | Craftsman - 102.01121 by Walker Turner
Photo Index - Sears | Craftsman - 102.01121 by Walker Turner
Making sure you're not a bot!
Making sure you're not a bot!
ad eBay - Craftsman 113 12" tilt band saw 1 1/8 hp electric motor 120v 1725 rpm 5/8" shaft
ad eBay - Craftsman 113 12" tilt band saw 1 1/8 hp electric motor 120v 1725 rpm 5/8" shaft
Craftsman 12 Inch Band Saw Update and Repair
Craftsman 12 Inch Band Saw Update and Repair

Choosing the Right Blade

Blade length is the first thing to confirm, because it's model-specific. Most 12-inch Craftsman band saws take an 80-inch blade, but there are exceptions, so measure your existing blade or check the manual before ordering a handful of spares. Getting this wrong means a blade that either won't tension or won't fit over the wheels at all.

For curve work, a 1/8- or 3/16-inch blade with 10 to 14 teeth per inch will turn tight radii that a wider blade simply cannot follow. For resawing and straight rips, step up to a 1/2-inch blade with three to six teeth per inch, which gives you the gullet capacity to clear sawdust and the beam strength to stay on line. A 1/4-inch, 6-to-10 TPI blade is the sensible middle ground that handles most general work, so it's the one worth keeping mounted by default.

AD

Tuning for Straight, Accurate Cuts

Start with tracking. Back the guides off completely, tension the blade to a firm pluck, and spin the upper wheel by hand while adjusting the tracking knob until the blade rides centered on the tire. Then set the upper and lower guide assemblies so the side bearings or blocks sit roughly the thickness of a dollar bill away from the blade, and the rear bearing sits just clear of the blade's back edge. Advance the blade by hand as you adjust so you don't accidentally push a guide into the teeth.

Once the blade is tracking and guided, check the table for square to the blade in both axes and set your fence parallel to the blade's actual cutting direction rather than to the mitre slot. If the saw drifts in a cut, the fix is usually a combination of more tension, better guides, and a fence angle adjusted to compensate. Dial it in with scrap and you'll find the saw holds a line far better than its price tag suggests.

Maintenance, Troubleshooting, and Long-Term Value

These saws last because they're simple. There's no computer, no variable-frequency drive, and no proprietary electronics to fail. What kills them is neglect: tires that dry out and crack, bearings that seize from packed sawdust, and motors that cook because someone resawed four-inch oak with a dull blade for an hour straight. A modest maintenance routine keeps all of that at bay.

Parts availability is the other reason a Craftsman 12-inch saw remains a smart buy. Belts, bearings, tires, guide assemblies, tension springs, and even replacement motors are all obtainable through aftermarket suppliers. You are not hunting for a unicorn part from a defunct brand, which is more than can be said for plenty of imported machines.

Routine Maintenance Checklist

Clean the tires regularly. Sawdust and pitch build up on the rubber or urethane, and a lumpy tire throws off tracking no matter how carefully you set the guides. A stiff brush and a little mineral spirits will restore grip quickly, and you should inspect the tire surface for cracking or flat spots at the same time.

Lubricate sparingly and correctly. The wheel bearings on most of these saws are sealed and need nothing, but the tension screw, the trunnion, and the guide adjustment threads benefit from a light machine oil or dry lubricant. Avoid heavy grease around the blade path, since it collects dust and creates a paste that accelerates wear. Then work through a short checklist every few months:

  • Brush or vacuum sawdust from the tires, guides, and motor vents
  • Check blade tension and re-tension if the blade has stretched
  • Inspect guide bearings for roughness and spin them by hand
  • Verify the table is square to the blade and the fence is parallel
  • Check the drive belt for glazing, cracking, or correct tension
  • Confirm the power cord and plug are free of cracks or exposed wire

Common Problems and Fixes

The most frequent complaint is the blade jumping off the wheels. That's almost always tracking or tension, not a defective saw. Worn tires, a stretched tension spring, or guides set too far from the blade will all cause it, and each is a cheap fix. If the blade slips under load even when properly tensioned, look at the drive belt before you blame the motor.

Vibration and poor cut quality usually trace back to a loose pulley set screw, a worn belt, or a blade with missing teeth. Motor issues are rarer but do appear on older units; a motor that hums without starting often needs a new start capacitor, which costs a few dollars and takes minutes to swap. If the motor runs hot or smells like burning insulation, stop using it and have it checked, because a burned winding is the one failure that genuinely sidelines the machine.

If you already own a 12-inch Craftsman band saw, spend an afternoon on tires, tension, and guides before you consider replacing it, because those three fixes recover most of the performance people assume is gone forever. If you're still shopping, look for a complete machine with the fence and stand included, inspect the tires and trunnion in person, and factor in the cost of a quality blade. Set up properly, this little saw will handle curves, tenons, and light resawing for another twenty years, and there's real satisfaction in running a well-tuned machine that cost you less than a single power tool accessory.

AD