10 Inch Craftsman Table Saw: Reviews, Buying Guide & Top Picks
If you have spent any amount of time browsing online marketplaces, estate sales, or the back corner of a neighbor's garage, you have probably crossed paths with a 10 inch Craftsman table saw. These machines have been a fixture in American home workshops for decades, and for good reason: they offer a genuine woodworking capability at a price that most hobbyists can actually justify. Whether you are ripping down plywood for a set of shop cabinets or cutting hardwood to width for a furniture project, a well-tuned 10-inch Craftsman can handle far more than its modest price tag suggests.
What makes the 10-inch size so appealing is that it hits a practical sweet spot. The blade is large enough to cut through standard 2x dimensional lumber and typical hardwood stock, yet the saw remains compact enough for a small shop or a garage that still needs to fit a car. Craftsman built these saws in several distinct generations, from heavy cast-iron contractor models to lightweight benchtop units, and understanding those differences is the key to picking the right one and getting the most out of it.
What Defines a 10 Inch Craftsman Table Saw
The "10 inch" designation refers to the diameter of the blade the saw accepts, and that single measurement drives almost everything else about the machine's capability. With a standard 10-inch blade set at 90 degrees, you get a maximum depth of cut around 3-1/4 inches, which clears a full 2x4 on edge and handles most furniture-grade hardwood without complaint. Tilt the blade to 45 degrees and that capacity drops to roughly 2-1/4 inches, still enough for beveled trim, chamfers, and most angled joinery.
Craftsman produced 10-inch table saws across a wide spectrum of build quality. The legendary 113 series contractor saws, many of them manufactured by Emerson Electric, featured cast-iron table tops, belt-driven motors, and a rugged trunnion assembly that still commands respect from woodworkers today. Later models, including the 137 and 315 series and the more recent Evolv line, moved toward lighter materials and direct-drive motors aimed at portability rather than longevity. Knowing which family you are dealing with tells you a lot about vibration, noise, and how well the saw will hold alignment over time.
Motor Options and Cutting Power
Most 10-inch Craftsman saws run on a universal motor drawing somewhere between 13 and 15 amps from a standard 120-volt household circuit, which translates to roughly 1-1/2 to 2 horsepower at the blade under ideal conditions. Belt-drive models separate the motor from the blade arbor, which reduces vibration and noise while making the motor easier to replace if it ever burns out. Direct-drive units are lighter and simpler, but they tend to be louder and less forgiving when you push a thick piece of maple through the blade too quickly.
In practical terms, that power level means you should feed stock at a controlled rate and let the blade do the work. A sharp, thin-kerf blade dramatically reduces the load on the motor, letting a 13-amp saw cut hardwoods that would otherwise bog it down. If you frequently work with thick stock, look for a belt-drive model with a 15-amp motor, and consider adding a dedicated 20-amp circuit so the saw is not competing with a shop vac or dust collector for current.
Rip Capacity, Table Size, and Fence Quality
Rip capacity is the distance from the blade to the right side of the fence, and on full-size Craftsman contractor saws it usually lands somewhere between 24 and 30 inches. That is enough to rip a sheet of plywood in half or crosscut a wide panel with the help of an outfeed table. Benchtop versions typically offer far less, often in the 12 to 18 inch range, which limits them to narrower stock and trim work.
The fence is arguably the weakest link on most factory Craftsman saws, and upgrading it is the single most impactful modification you can make. Stock fences on older models often flex under pressure and struggle to stay parallel to the blade, which creates binding and burn marks. Aftermarket options like a T-square style fence or a shop-built wooden fence clamped to a sturdy rail system can transform the saw's accuracy for a fraction of the cost of a new machine.
Setting Up and Running Your Craftsman Saw
Getting a used Craftsman table saw dialed in is where the real satisfaction begins, because these machines respond extremely well to careful setup. Start by assembling the stand and extension wings, then verify that the table surface is flat and coplanar across all sections. Any twist or dip in the table will telegraph directly into your cuts, so shim the wings as needed before you tighten everything down.
From there, the two alignment tasks that matter most are squaring the blade to the miter slots and setting the fence parallel to those same slots. Once the blade and fence agree with each other, every cut becomes predictable. Many woodworkers also build a simple crosscut sled and an outfeed support table, both of which turn a basic Craftsman into a far more capable and safer machine.
Blade Selection and Alignment
A general-purpose 40-tooth combination blade is the right starting point for almost any 10-inch Craftsman saw. It rips acceptably and crosscuts cleanly, and a thin-kerf version puts less strain on a modest motor. If you do a lot of ripping, a 24-tooth ripping blade speeds things up considerably, while a high-tooth-count crosscut blade leaves glassy end grain on trim and furniture parts. Dado stacks up to 3/4 inch wide will also fit on most of these saws, though you should check your arbor length and confirm your particular model supports them.
For alignment, unplug the saw and raise the blade to its highest position. Use a dial indicator or a combination square against the blade body, not the teeth, and measure the distance to the left miter slot at both the front and rear of the blade. Loosen the trunnion bolts and tap the assembly until the measurements match, then re-tighten and recheck. Small adjustments here pay off every single time you push a board through.
Safety Practices and Routine Maintenance
Older Craftsman table saws frequently lack a riving knife, which is the modern safety feature that prevents stock from pinching the blade and kicking back. If your saw has only an antiquated blade guard and splitter, use them whenever a cut allows, and always rely on push sticks, featherboards, and a Gripper-style push block for narrow rips. Never stand directly behind the blade, keep your hands clear of the cut line, and disconnect power before changing blades or making adjustments.
Maintenance is simple but consistent work. Wax the cast-iron table with paste wax to keep boards gliding, brush out sawdust from the trunnions and elevation screws, and apply a dry lubricant to the height and tilt mechanisms a couple of times a year. On belt-drive models, check the belt for cracks and set proper tension so the blade spins without slipping. Replacing a worn belt and giving the arbor bearings a listen for rumble can add years of smooth service to a saw that cost you very little.
A 10 inch Craftsman table saw is one of the best values in home woodworking, especially if you are willing to spend a Saturday afternoon tuning it up. Pick a belt-drive contractor model if you have the space, upgrade the fence, invest in two quality blades, and you will have a machine that handles everything from framing lumber to fine cabinetry. Keep an eye on local listings and estate sales, bring a square and a straightedge when you go look, and do not be afraid of a little rust on the table surface. With a bit of patience and a fresh coat of wax, these saws still earn their keep decades after they left the factory.