1 3/8 on a Ruler: How to Find and Read This Measurement Easily
If you have ever stared at the tiny tick marks between the inch numbers on a ruler, you are not alone. Understanding exactly where 1 3/8 on a ruler falls can turn a frustrating measurement into a quick, confident read. This mixed number is common in woodworking, sewing, and home repair, yet it often causes hesitation because it sits between familiar fractions.
Learning to locate 1 3/8 is mostly about recognizing the pattern of fractions. Once you know how the marks are spaced, you can find it on almost any inch ruler, whether it is marked in eighths, sixteenths, or even thirty-seconds. This guide breaks down the process step by step so you can measure 1 3/8 inches accurately every time.
What 1 3/8 Means on an Inch Ruler
1 3/8 is a mixed number: one whole inch plus three-eighths of another inch. In decimal form, it equals 1.375 inches. That makes it larger than 1 1/4 (1.25) and smaller than 1 1/2 (1.5), placing it exactly halfway between those two common fractions.
On a typical ruler, the inch is divided into smaller equal parts. The denominator tells you how many parts make up one inch. A ruler marked in eighths has eight spaces per inch, so 3/8 means three of those spaces. A ruler marked in sixteenths has sixteen spaces per inch, and 3/8 becomes 6/16, so you count six small sixteenth marks.
Locating 1 3/8 on a Standard Inch Ruler
Start at the 1-inch mark, not at the end of the ruler unless the ruler begins at zero. From there, move right and count the 1/8 marks: 1 1/8, 1 1/4, 1 3/8. The third eighth mark after the 1-inch line is your target. If the ruler labels only whole inches, you will see the mark sitting between 1 1/4 and 1 1/2.
To confirm your position, notice that 1 3/8 is exactly halfway between 1 1/4 and 1 1/2. If you are reading a ruler with longer 1/4 marks, the 1 3/8 mark will not be as long as those quarter marks, but it will be longer than the 1/16 marks. This visual hierarchy helps you avoid counting the wrong tick.
Reading 1 3/8 on a Ruler with 16th Increments
Many rulers and tape measures divide each inch into sixteenths. Because 3/8 equals 6/16, 1 3/8 is the same as 1 6/16. From the 1-inch line, count six small sixteenth marks to the right. The sequence is 1 1/16, 1 1/8, 1 3/16, 1 1/4, 1 5/16, and then 1 3/8. The sixth mark is your measurement.
If you lose count, use the quarter marks as landmarks. The 1 1/4 mark is four sixteenths past the inch, and 1 1/2 is eight sixteenths past. The 1 3/8 mark sits two sixteenths after 1 1/4 and two sixteenths before 1 1/2. That gives you a quick way to double-check without starting over from zero.
Practical Ways to Use 1 3/8 Inches
Measurements like 1 3/8 inches show up in real projects more often than you might expect. A piece of trim, a seam allowance, a drill bit, or a small gap might call for exactly 1.375 inches. Knowing how to find that spot on a ruler keeps your work precise and reduces wasted material.
Whether you are cutting a board, marking fabric, or checking a replacement part, the ability to read 1 3/8 on a ruler saves time. It also helps you convert the measurement when a project uses decimals or metric units. The more comfortable you become with this fraction, the easier it is to switch between inches, fractions, and millimeters.
Converting 1 3/8 to Decimals and Millimeters
Converting 1 3/8 to a decimal is simple: divide 3 by 8 to get 0.375, then add the whole inch. The result is 1.375 inches. This decimal form is useful when you are entering measurements into a calculator, using digital calipers, or working with software that does not accept fractions.
For metric conversions, multiply 1.375 by 25.4, since one inch equals 25.4 millimeters. The result is 34.925 millimeters, or about 3.49 centimeters. On a metric ruler, you would mark just under the 35-millimeter line. This conversion is especially helpful when a project mixes imperial and metric hardware.
Common Mistakes When Measuring 1 3/8
One frequent mistake is confusing 1 3/8 with 1 5/8. They are one quarter inch apart, but that difference can ruin a cut or a seam. Remember that 1 3/8 is smaller than 1 1/2, while 1 5/8 is larger than 1 1/2. Always double-check which side of the half-inch mark you are on.
Another error is starting the measurement from the very edge of a worn ruler. If the first tick is damaged or the ruler has a metal hook, confirm where zero actually is. Also, make sure you are reading the inch side, not the centimeter side. A quick glance at the numbers will prevent a costly mix-up.
With a bit of practice, finding 1 3/8 on a ruler becomes second nature. Try marking a scrap piece of paper at 1 3/8 inches, then measure it with a different ruler to confirm your reading. The more you train your eye to see the eighths and sixteenths, the faster and more accurate your measurements will be.